Pfeiffer Vacuum HiPace 800 P Operating Instructions Manual Download

Page: 33 / 39

Accessories

Accessories

Designation

DN 200 ISO-K

DN 200 CF-F

DN 200 ISO-F

TPS 400, mains pack for wall/standard rail fitting

PM 061 343 -T

Wall rail fitting TPS 110/180/310/400

PM 061 392 -T

TPS 401, mains pack 19" rack module 3HU

PM 061 347 -T

Front panel kit for TPS 401

PM 061 396 -T

DCU 400, Display control unit incl. power supply

PM C01 823

DCU 002, Display control unit

PM 061 348 -T

HPU 001, handheld programming unit

PM 051 510 -T

Accessories package for HPU - Power supply, software and PC cable

PM 061 005 -T

Mains cable with Euro-style safety plug, IEC power socket (straight), 230 V
AC, 3 m

P 4564 309 ZA

Mains cable with UL plug, IEC power socket (straight), 115 V AC, 3 m

P 4564 309 ZE

Mains cable with UL plug, IEC power socket (straight), 208 V AC, 3 m

P 4564 309 ZF

Connection cable for linking HiPace with TC 400 to power supply TPS/DCU
310/311/400/401

PM 061 352 -T

Venting valve screened, 24 V DC, G 1/8", for connection to TC 400/1200 and
TM 700

PM Z01 291

Venting valve, 24 V DC, G 1/8" without cable

PM Z01 293

TTV 001, air drier for venting turbopumps

PM Z00 121

Venting flange, DN 10 KF, G 1/8"

PM 033 737 -T

Banjo fitting, G 1/8"

PM 143 877 -T

Air cooling for HiPace 400 and HiPace 700 with TC 400

PM Z01 303

Air cooling with cable for TC 400, plug M12 for Tele TC cable 400

PM Z01 304

Heating jacket for HiPace 400 / 700 / 800 with TC 400 / TCP 350, 230 V AC,
Euro-style safety plug

PM 061 369 -T

Heating jacket for HiPace 400 / 700 / 800 with TC 400 / TCP 350, 208 V AC,
UL plug

PM 061 370 -T

Heating jacket for HiPace 400 / 700 / 800 with TC 400 / TCP 350, 115 V AC,
UL plug

PM 061 371 -T

Backing pump relay box, single phase 5 A, for TC 400/1200 and TM 3000

PM 061 374-T

Backing pump relay box, single phase 20 A, for TC 400/1200, TCP 350 and
TM 3000

PM 061 375 -T

TVV 001 fore-vacuum safety valve, 230 V AC

PM Z01 205

TVV 001 fore-vacuum safety valve, 115 V AC

PM Z01 206

Sealing gas valve, screened, for HiPace 1200-2300 with TC 1200

PM Z01 313

Sealing gas throttle for HiPace 1200-2300

PM Z01 318

USB converter to RS-485 interface

PM 061 207 -T

Interface cable, M12m/M12, 3 m

PM 061 283 -T

Interface cable, 3 m, M12, straight, 90°

PM 061 791 -T

Y-Connector M12 to RS-485

P 4723 010

Y-Connector M12 for accessories

P 4723 012

Remote plug for TC 400/1200, with bridges

PM 061 378 -X

Power supply plug TC 400, straight

P 4723 100

Power supply plug TC 400, angled

P 4723 101

Remote adapter for RS-485

PM 061 649 -T

Connection cable, plug M12, RJ 45, 3 m

PM 051 726 -T

Power supply plug TPS 110/180/310/400 DC out

P 4723 102

Tele TC cable 400, 3 m

PM 061 595 AT

Extension cable for accessory M12 on M12

PM 061 747 -T

Power failure venting valve, screened, 24 V DC, G 1/8" for connection with TC
400, TM 700

PM Z01 331

HiPace-ACP Connection cable

PM 071 142 -X

Banjo fitting, G 1/8"

PM 016 787 -T

Screw-in flange, DN 16 ISO-KF, G 1/8"

PM 016 780 -T

Plug-in connection for 6 mm hose, G 1/8"

PM 016 781 -T

Plug-in connection for 8 mm hose, G 1/8"

PM 016 782 -T

Hose nozzle for 9 mm hose, G 1/8"

PM 016 783 -T

Centering ring with multifunction coating, DN 200 ISO-K/-F

PM 016 220 -U

Centering ring with multifunction coating and integrated protection screen, DN
200 ISO-K/-F

PM 016 222 -U

Summary of Contents for HiPace 800 P








































Search results

Summary of Contents for HiPace 800 P

Reviews:

Related manuals for HiPace 800 P

Brands by name

Popular brands

Pfeiffer Vacuum HiPace 800 P, Operating Instructions Manual

Search results

Summary of Contents for HiPace 800 P

Reviews:

Related manuals for HiPace 800 P

Brands by name

Popular brands