ICS –Quick reference card
V4.10 dd 12-11-2015
For additional information see manual: OM_xx_ICS_OnBoard_Configuration (xx = Language code)
2 of 2
K450 Settings
Transportation Mode (WC19)
Entry:
Button 1, 2 and 7
(all led’s green – led 7 flashes red/led 8 flashes green)
Setting:
Button 1 or 5
Save:
Button 8 (2 sec)
Transportation Mode OFF
Transportation Mode ON
Transportation Mode: Hook position
Entry:
Button 6 and 8
all led’s start toggle green.
Release Button 6 and 8 and press Button 4 (for appr. 5 sec):
Led indication changes and seat starts to move
Setting:
Button 1 or 5
to move seat elevator up/down
Button 2 or 6 to move hooks backwards/forwards
Button 3 or 7 to move hooks up/down
Button 4
to operate transportation mode
Adjustment process
Press Button 4 until hooks are close to engage loops.
Use Buttons 2/6 and 3/7 to engage hooks:
-Hook centered around loop
-Slight pressure on loop
Save:
Button
8
Seat tilt
Entry:
Button 1, 2 and 7
(all led’s green – led 7 flashes red/led 8 flashes green)
Setting:
Button 3 or 7
Save:
Button 8 (2 sec)
Without tilt
With tilt
Seat width / Armrest type restriction
Entry:
Button 3, 4 and 6
(all led’s green – keep pressing until rapid beep (5sec)
led 7 flashes red/led 8 flashes green)
Setting:
Button 1 or 5
Save:
Button 8 (2 sec)
No
restriction
MX armrest and seat 25-30-35cm / 10-12-14” wide
PSjr armrest and seat 25-30cm / 10-12” wide
Small
restriction
PSjr armrest and seat 35cm / 14” wide
High
restriction
MX armrest and seat 40cm / 16” wide
PSjr armrest and seat 40cm / 16” wide
VS Settings
Leg rest type
Entry:
Button 1, 2 and 7
(all led’s green – led 7 flashes red/led 8 flashes green)
Setting:
Button 1 or 5
Save:
Button 8 (2 sec)
Stand NO Drive
Stand and Drive
VS Standing properties
Entry:
Button 5 and 7 (all led’s green – led 8 toggles green/red)
Sequence A (left icon) / Sequence B (right icon)
Setting:
Pre-defined sequence A: Button 1, 2 or 3 / Pre-defined sequence B: Button 5, 6 or 7
Pre-defined sequence 1 (45sit – stand) Sequence A: button 1 / Sequence B: button 5 (led 1: green and hold until it gets red)
Pre-defined sequence 2 (90sit – stand) Sequence A: button 2 / Sequence B: button 6 (led 3: green and hold until it gets red)
Pre-defined sequence 3 (lay – stand)
Sequence A: button 3 / Sequence B: button 7 (led 5: green and hold until it gets red)
Maximum stand – seat height
Setting: Standing
Button 1 or 5
Setting: Seat height:
Button 2 or 6
Move standing to max position for user and at the same time keep footplate on the floor by changing the seat height
Seat height: led 8: green=OK / red=Outside range.
Save:
Button 8 (2 sec) short beep – led’s 7 and 8: green
Switch chair off.
VS Take Me Down (Emergency UN-Standing)
Entry:
Button 6 and 8
(after appr. 30 sec all led’s red – all Led’s toggle flashes
green)
Button 1 and 5:
Standing actuator
Button 2 and 6:
Seat elevator
Button 3 and 7:
Backrest actuator
Button 4 and 5:
Legrest actuator
Switch chair off.
CorpusAPE
(>V12)
/ CorpusVS
(>V9)
- Specific Attributes
Disable Drive in Standing
Entry:
Button 1, 2 and 7
(all leds green – led 7 flashes red
/led 8 flashes green)
Setting: Button 1 or 5
Save:
Button 8 (2 sec)
Access to CorpusAPE / CorpusVS attributes
Entry:
Button 5 and 7
(all leds green – led 7off / led 8 flashes red/green)
-Button 1: Standing sequence 1 / transfer sequence adjustment
-Button 2: Standing sequence 2 adjustment
-Button 3: Adjustment of Legrest extension in standing/transfer position
-Button 4: Ground clearance / Ground touch adjustment
-Button 7: Set IRM positions (See other side: IRM Position)
Note: Pressing button 1-3 > 15 sec resets selected function to presets
Pressing button 4 > 15 sec sets ground clearance/touch to 0
(Led 1-4 start flashing green – release: reset)
Ground Touch / Ground Clearance
The Ground Touch procedure should be performed first and redone
after every mechanical adjustment of the footplate height!
Entry:
Button 4 (Led 4 - solid green)
Setting: Button 1-5: Seat elevator
Button 2-6: Set Legrest extension
Save:
Button 7: Save ground clearance (Led 6)
Button 8: Save ground touch (Led 8)
Led 6 / 8 - flashing green, new position can be saved
Led 6 / 8 - solid green while holding button8, position saved
Led 6 / 8 - solid yellow, can't save leg extension position
Legrest extension for standing / transfer
Entry:
Button 3 (Led 3 - solid green)
Setting: Seat in the maximum standing/transfer position:
Button 1-5: Position footplate to required extension
Save:
Button 8: Save legrest extension
Led 8 - flashing green, new position can be saved
Led 8 - solid green while holding sw8, position saved
Led 8 - solid yellow when seat is in a position that doesn't allow saving
Standing sequence 1 / Transfer sequence
Entry:
Button 1:
Standing Sequence 1 / Transfer Sequence adjustment (Led 1: solid red)
Checkpoints (CP1-4) are indicated by Led 1-4 Green
Setting:
Button 1-5: Control stand sequence up/down
Button 2-6: Set backrest angle
Button 3-7: Set legrest angle
Save:
Button 8
Process:
Press Button 1 until CP1 is reached (LED 8 flashes green)
Set back/leg and save with button 8
Press Button 1 until required stand position: CP2 (LED 8 flashes green)
Set back/leg and save with button 8
Press Button 5 until CP3 is reached (LED 8 flashes green)
Set back/leg and save with button 8
Press Button 5 until CP4 is reached (LED 8 flashes green)
Set back/leg and save with button 8
Led 8 - flashing green, position can be saved
Led 8 - solid green while holding button 8, position saved
Led 8 - flashing red while holding button 8, can't save sequence position
Note: In CP2 de previous max set standing / transfer angle can be overruled
by pressing Button 1 for more than 5 sec.
Standing sequence 2
Entry:
Button 2
Standing Sequence 2 adjustment (Led 2: solid red)
Check Point (CP1-4) are indicated by Led 1-4 Yellow
Follow the same procedure as for Sequence 1
