Perlick Draft Arm Installation Instructions Manual Download Page 18

PERLICK CORPORATION

   8300 W. Good Hope Road,  Milwaukee, WI  53223   •   800.558.5592   •   perlick.com

PRODUCT INSTALLATION INSTRUCTIONS

   

   Dispensing Towers

DISPENSING TOWERS

DRAFT ARMS, 2-6 FAUCET TEE TOWERS, LUCKY AND PANTHER TOWERS

18

LUCKY AND PANTHER TOWER INSTRUCTIONS, Continued

Attaching the Beer Line to the Lucky or Panther Towers

1.  On one end of the beer connector, cut off 

the beer nut fitting. 

2.  Push the beer line connector end over the 

barbed end of the product supply line and 

tighten with a clamp using a 1/4” nut driver or 

slotted screwdriver.

3.  Insert the rubber washer into the other end 

of the beer line and attach to the keg coupler.  

Tighten with an adjustable wrench but do not 

over-tighten.
4.  Repeat for each additional supply tube.

Attaching the Gas Line Tubing

1.  Attach one end of the gas line to a valve on the air distributor  

manifold and tighten with a hose clamp. 
2.  Repeat for each additional product line.
3.  Attach the other end of the gas line to the keg coupler and tighten 

with a hose clamp.

Attaching the Tapping Hole Covers

1.  To comply with NSF standards, please attach the tapping hole covers provided.  
2.  The two-piece cover can be adjusted to tighten snugly around beer lines and air scoop  

tubing.
3.  Position the covers tightly around the tubing and mount to the bottom side of the cabinet 

top using a cordless drill with a 5/16” socket head bit and the self-drilling screws provided. 

Please refer to Diagram 7 in the Appendix.

3

1

3

1

2

2

1

1

3

Summary of Contents for Draft Arm




























Reviews: