Perle IDS-509F Hardware Installation Manual Download Page 9

Page: 9 / 37

Overview 7

IDS-509F Hardware Installation Guide

LED Indicators

P (Power Inputs)

Sys (System Status)

Alr (Alarm)

BC (Backup Coupling)

State

Description

Green

P1 and P2 Power inputs within specifications

Yellow

P1 or P2 Providing power within specifications

Red

Neither P1 or P2 providing power within specifications

State

Description

Green - blinking (after power on)

System booting

Green - solid

System ready/operating normally

Green - blinking slowly

Fast Setup Mode activated/port available

Green - blinking fast

Fast Setup Mode activated/no port avail

able

Red

Hardware fault or firmware load error

State

Description

Off

No alarms configured

Green - solid

Alarms configured, but no alarms detected

Red - solid

Alarm condition detected

Red - blinking

Alarm condition detected and Alarm Relay activated

State

Description

Off

Backup Coupling not enabled

Green - solid

Backup Coupling Link enabled

Summary of Contents for IDS-509F






































Search results

Summary of Contents for IDS-509F

Reviews:

Related manuals for IDS-509F

Brands by name

Popular brands

Perle IDS-509F, Hardware Installation Manual

Search results

Summary of Contents for IDS-509F

Reviews:

Related manuals for IDS-509F

Brands by name

Popular brands