manualshive.com logo in svg

PerkinElmer OilExpress System, User Manual

Share
Download
PerkinElmer OilExpress System User Manual Download Page 49

Unpacking and Installation . 49 

Installing the Flowcell in the Sample Shuttle 

 

 

 

WARNING 

DO NOT use the OilExpress System when the sample compartment lid is 

fitted. Flammable vapor may seep through instrument seals and gaskets 

and accumulate under the lid, where it could cause a fire or explosion 

hazard. 

1.

 

Unpack the flowcell. 

2.

 

Slide the flowcell into the sample shuttle (Figure 24). 

3.

 

Make sure that the tubing cannot obstruct the optical beampath. 

 

Figure 24 Sample shuttle accessory and flowcell fitted 

Waste Container 

We recommend that you use a waste container that is larger than the solvent bottle. Then, if 

you empty the waste container whenever you refill the solvent bottle, the waste container 

will not overflow. 

The waste drains into the container by gravity, so the container should stand on a surface 

that is at least 90 cm below the bench on which the OilExpress System is located. 

Fitting waste tubing 

1.

 

Attach the waste tubing to the hose connector at the rear of the transfer/wash port. 

2.

 

Insert the waste tubing into the hole on the rear right-hand side of the base plate of the 

Autosampler. 

3.

 

Adjust the routing of the tubing so that it is not kinked. 

4.

 

Place the other end of the waste tubing in the waste container. 
Ensure that the end will not be immersed in the waste. 

CAUTION 

Make sure that the ends of the tubing do not become immersed in the 

waste or the operation of the analyzer will be impaired. 

Summary of Contents for OilExpress System







































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands