Performax 241-1395 Owner'S Manual Download Page 5

 

 
 

 

SPECIFIC SAFETY 

– cont’d 

 
Do not use worn or damaged 
screwdriver bits.

 Worn or damaged 

screwdriver bits will not drive the screw 
properly and may jump out of the screw 
head, causing possible injury. 
 

Always insert the magnetic bit holder 
fully into the collet.

 If not fully inserted, 

the magnetic bit holder may jump out of 
the collet and cause damage to the 
workpiece or possible injury. 
 
 

 
 
 
 
        

WARNING:

 

The lithium-ion battery is 

an integral part of the tool. If it no longer 
charges properly or is damaged, the tool 
and battery must not be discarded as 
household trash, burnt or thrown into 
water. The tool and battery must be 
disposed of as hazardous waste in 
accordance with all municipal 
requirements. 

 
Do not incinerate a discarded battery.

 It 

can explode in a fire. 

 
Do not use an extension cord.

 Plug the 

charger cord directly into an electrical 
outlet. 
 

Charge the battery only with the 
charger supplied with this cordless 
screwdriver.

 

 

Do not use the charger in wet or damp 
conditions.

 It is intended for indoor use 

only. Do not use the charger near sinks or 
bathtubs. Do not immerse the charger in 
water. 
 

 
 
 
Do not allow the cord to hang over the 
edge of a table or counter or touch hot 
surfaces.

 The charger should be placed 

away from sinks and hot surfaces.

 

 
Do not use charger to charge any 
batteries other than the cordless 
screwdriver battery.

 Other batteries may 

explode. 

 
Do not operate charger if cord or plug is 
damaged.

 Replace damaged cord and 

plug immediately. 
 

Do not operate charger if it has 
received a sharp impact,

 been dropped 

or otherwise damaged in any way. Have a 
qualified technician examine the charger 
and repair it if necessary. Do not 
disassemble the charger. 
 

For best results,

 charge the battery when 

the temperature range of the battery and 
the work area is 0

–45° C (32–113° F). 

 
Unplug the charger when not in use

 and 

before cleaning or maintenance.

 

 
Do not abuse the cord.

 To reduce the risk 

of damage to the electric cord or plug, 
never carry the charger by the cord or 
yank the cord to unplug. Always grasp the 
plug and pull to disconnect. Always keep 
the cord away from heat, oil and sharp 
edges.

BATTERY & CHARGER 

SAFETY 

SPECIFIC SAFETY 

 

Summary of Contents for 241-1395

















Reviews: