manualshive.com logo in svg

Performax 241-0988, Operating Manual, Page: 5 / 16

Share
Download
Performax 241-0988 Operating Manual Download Page 5

5

ELECTRICAL SAFETY

 

 

 Double insulated tools are equipped with 

a polarized plug (one blade is wider than 

the other). This plug will fit in a polarized 

outlet only one way. If the plug does not fit 

fully in the outlet, reverse the plug. If it still 

does not fit, contact a qualified electrician 

to install a polarized outlet. Do not change 

the plug in any way. 

Double insulation 

 eliminates the need for the three wire 

grounded power cord and grounded power 
supply system.

 

 

Avoid  body  contact  with  grounded  surfaces  such  as  pipes,  radiators, 

ranges and refrigerators. 

There is an increased risk of electric shock if your 

body is grounded.

 

 

Don’t  expose  power  tools  to  rain  or  wet  conditions. 

Water  entering  a 

power tool will increase the risk of electric shock.

 

 

Do not abuse the cord. Never use the cord to carry the tool or to pull 

the plug from an outlet. Keep the cord away from heat, oil, sharp edges 

or moving parts. Replace damaged cords immediately. 

Damaged cords 

increase the risk of electric shock.

 

 

When  operating  a  power  tool  outside,  use  an  outdoor  extension  cord 

marked “W-A” or “W”. 

These cords are rated for outdoor use and reduce the 

risk of electric shock.

PERSONAL SAFETY

 

 

Stay  alert,  watch  what  you  are  doing  and  use  common  sense  when 

operating  a  power  tool.  Do  not  use  the  tool  while  tired  or  under  the 

influence of drugs, alcohol, or medication. 

A moment of inattention while 

operating power tools may result in serious personal injury.

 

 

Dress properly. Do not wear loose clothing or jewelry. Contain long hair. 

Keep  your  hair,  clothing,  and  gloves  away  from  moving  parts.

  Loose 

clothes, jewelry, or long hair can be caught in moving parts.

 

 

Avoid accidental starting. Be sure that the switch is off before plugging 

in the tool. 

Carrying tools with your finger on the switch or plugging in tools 

that have the switch on invites accidents.

 

 

Remove adjusting keys or wrenches before turning the tool on. 

A wrench 

or a key that is left attached to a rotating part of the tool may result in personal 
injury.

120V~ ,60Hz

Summary of Contents for 241-0988

















Reviews:

No comments