REPLACEMENT PARTS AVAILABLE
WARNING
1-1/2 Ton LOW PROFILE
ALUMINUM FLOOR JACK
OWNER’S MANUAL
Stock Number W1630
FOR YOUR SAFETY,
please read these instructions carefully and retain them for future use.
LIMITED WARRANTY
PERFORMANCE TOOL extends only the following warranties, and only to original retail purchasers. These warranties give
specific legal rights. Except where prohibited by local law, the law of the State of Washington governs all warranties and all
exclusions and limitations of warranties and remedies. There may be other rights which vary from state to state.
PERFORMANCE TOOL warrants the product to be free from defects in materials and workmanship under normal use and
service. A defective product may be returned for a free replacement within 90 days from the date of purchase, provided that
product is returned to place of purchase immediately after discovery of defect. After 90 days and up to 1 year from date of
purchase, PERFORMANCE TOOL will replace at no charge any parts which our examination shall disclose to be defective and
under warranty. These warranties shall be valid only when a sales receipt showing the date of purchase accompanies the
defective product or defective part(s) being returned. For part(s) after 90 days, please remit your request, postage prepaid to:
PERFORMANCE TOOL, P.O. Box 24086 Seattle, WA 98124
These warranties exclude blades, bits, punches, dies, bulbs, fuses, and other consumables which must be replaced under normal
use and service. These warranties shall not apply to any product or part which is used for a purpose for which it is not designed,
or which has been repaired or altered in any way so as to affect adversely its performance or reliability, nor shall these warranties
apply to any product or part which has been subject to misuse, neglect, accident or wear and tear incident to normal use and
service.
PERFORMANCE TOOL does not authorize any other person to make any warranty or to assume any liability in connection with
its products.
Except for warranties of title and the limited express warranties set forth above, PERFORMANCE TOOL makes no express or
implied warranties of any kind with respect to its products. In particular, PERFORMANCE TOOL makes no implied warranty of
merchantability and no implied warranty of fitness for any particular purpose, except that for goods purchased primarily for
personal, family or household use and not for commercial or business use, PERFORMANCE TOOL makes an implied warranty of
merchantability (and, if otherwise applicable, an implied warranty of fitness for a particular purpose), but only for the particular
qualities or characteristics, and for the duration, expressly warranted above. The laws on limitation of implied warranties may
differ from state to state, so the above limitations may not apply in all cases.
PERFORMANCE TOOL shall not be liable for consequential, incidental or special damages resulting from or in any manner
related to any product, or to the design, use, or any inability to use the product. The sole and exclusive remedy for a defective
product or part shall be the repair, or replacement thereof as provided above. The laws on limitation of remedies or on
consequential, incidental or special damages may vary from state to state, so the above limitations may not apply in all cases.
Copyright © 2005 PERFORMANCE TOOL – All rights reserved
W1630CK
Ram Repair Kit
W1630-29
Front Wheel
W1630-10
Rear Wheel Saddle
W1630-9
Rear Wheel
W1630-24
Release Valve Rod Assembly
W1630-19
Handle Base Screw
W1630-20
Handle Assembly
W1630-41
Saddle
PART NO.
DESCRIPTION
PART NO.
DESCRIPTION
DO NOT UNDER ANY CIRCUMSTANCES, REMOVE THE SAFETY VALVE SEAL
BOLT AND ADJUST THE VALVE.
PLEASE USE THE FOLLOWING DIAGRAM WHEN THERE IS A NEED TO FILL AND
BLEED THE JACK’S OIL RESERVOIR.
Included with the jack is a Bleeder Valve that can be used instead of the oil reservoir seal
bolt. Simply replace the seal bolt with the Bleeder Valve. The seal washer must also be
used. To add oil to the jack, remove the bleeder valve and add oil as per manual
instructions, then replace the valve. The operation of the Bleeder Valve is completely
automatic and no adjustment by the consumer is needed. To bleed the jack, turn the
handle 1-1/2 turns counter clockwise and pump the handle assembly several times to
purge air from the hydraulic system. The valve will also automatically purge air from the
hydraulic system during regular use.
