Performance Tool M702, Owner'S Manual

Page: 2 / 6

2
SPECIFICATIONS
Specifications are subject to change without notice
IMPORTANT SAFETY INFORMATION
WARNING!
READ, UNDERSTAND AND FOLLOW ALL INSTRUCTIONS AND WARNINGS BEFORE OPERATING THIS TOOL.
FAILURE TO DO SO MAY RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE AND WILL VOID WARRANTY.
Air Pressure: ................................... 30 - 90 P.S.I.
Spray pattern: ..................................... 10 - 12 in.
Spray Head & Needle: .............................1.0 MM
Cup capacity: ..........................................2,000cc
1. Keep work area clean. Cluttered areas invite injuries.
2. Observe work area conditions. Do not use machines or power
tools in damp or wet locations. Don’t expose to rain. Keep
work area well lighted. Do not use electrically powered tools
in the presence of flammable gases or liquids. Always keep
work area free from obstructions and well ventilated.
3. Keep children away. Children must never be allowed in the
work area. Do not let them handle machines, tools, hoses or
extension cords.
4. Store idle equipment. When not in use, tools must be stored in
a dry location to inhibit rust. Always lock up tools and keep out
of reach of children and other untrained persons. Switch off all
unused electrical tools when stored. Tools are dangerous in
the hands of untrained users.
5. WARNING: All persons in the work area must always wear
approved eye and ear protection and approved breathing
apparatus when this spray gun is in operation.
6. Work Safe. Do not wear loose clothing or jewelry that could
become caught by moving parts, causing injury. Operate tool a
safe distance from yourself and others in the work area. Keep
proper footing and balance at all times. Do not reach over or
across running machines, hoses, etc.
7. Stay alert. Watch what you are doing, use common sense. Be sure all
personnel are clear of the direction of the spray gun. Do not operate
any tool when you are tired.
8. Do not operate any tool if under the influence of alcohol or
drugs. Read warning labels on prescriptions to determine if
your judgment or reflexes are impaired while taking drugs. If
there is any doubt, do not operate any tool.
9. Never aim spray gun at anyone. Do not spray near sparks,
open flame, lit cigarettes, pilot lights, space heaters or any
other potential ignition source. DO NOT SMOKE IN WORK
AREA.
10. Follow air source manufacturers directions for connection of
regulators, filters, and other accessories to air source. Do not
install quick couplers directly on tool as they put unnecessary
strain on the air inlet threads possibly causing them to wear
out prematurely. Instead, install them on a short length of air
hose attached to the tool.
11. Follow manufacturers instructions and safety information
to ensure safe handling and proper use of paints, lacquers,
Avg. Air Consumption (CFM): ................3.5 - 11
Fluid Inlet (NPS): .......................................3/8 in.
Air Inlet (NPS): ...........................................1/4 in.
Hose Size (ID): ...........................................3/8 in.
thinners, base coats, etc. Do not use latex or other heavy
paints. They are not recommended for this spray gun.
12. Always disconnect spray gun from air source before
disassembly.
13. Warning! Solvents Trichloroethane and Methylene Chloride
(Dichloromethane - sometimes called Methylchloride) can
chemically react with the Aluminum used in most spray
equipment creating an explosion hazard. Read the label or
data sheet from the material you intend to spray. NEVER use
any material containing these solvents. If unsure as to the
composition of your material, check with your supplier. Do not
use acids for cleaning.
14. Check for damaged parts. Before using any tool, any part that
appears damaged should be carefully checked to determine
that it will operate properly and perform its intended function.
Check for alignment and binding of moving parts; any broken
parts or mounting fixtures; and any other condition that may
affect proper operation. Any part that is damaged should be
properly repaired or replaced by a qualified technician.
15. Maintenance. For your safety, maintenance should be
performed regularly by a qualified technician using original
PERFORMANCE TOOLS® replacement parts. Failure to
do so can lead to accidents for the operator. Use of any
other parts will void the warranty. Only use accessories
intended for use with this tool. Approved accessories are
available from Performance Tool®. Use only accessories
that are recommended by the manufacturer for your model.
Accessories that may be suitable for one tool may become
hazardous when used on another tool.
WARNING: This product and its packaging contain a chemical
known to the State of California to cause cancer, birth defects, or
other reproductive harm.
WARNING: The warnings, cautions, and instructions discussed
in this instruction manual cannot cover all possible conditions and
situations that may occur. It must be understood by the operator
that common sense and caution are factors which cannot be built
into this product, but must be supplied by the operator. Read
and understand all of the instructions provided in the instruction
manual of this product, as well as, any other tool (s) used with this
product.