Perfomance Tool M662, Owner'S Manual, Page: 1 / 2

1 Body 1
2 O-Ring 2
3 O-Ring 1
4 Pin 1
5 O-Ring 3
6 Tube 1
7 Trigger Spring 1
8 Trigger 1
9 Screw 2
10 Trigger Pin 1
11 Exhaust Diffuser 1
12 Screw 2
13 Connector 1
14 Bearing 2
15 Rear Cover 1
16 Rotor 1
17 Blade 5
18 Cylinder 1
19 Pin 2
20 Front Cover 1
21 Gasket 1
22 Gear 3
23 Gear Pin 3
24 Spindle 1
25 Ring 1
26 Bearing 2
27 Lock Ring 1
28 Washer 1
29 Spindle Nut 1
30 Bearing 1
31 Blade Housing 1
32 Screw 1
33 Block 1
34 Center Blade 2
35 Left Blade 2
36 Bushing 1
37 Right Blade 2
38 Wrench 2
HEAVY DUTY METAL SHEAR
OWNER’S MANUAL
Stock Number M662
SPECIFICATIONS:
Cutting Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 GA
Air pressure (P .S .I .) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Average air consumption (C .F .M .) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Free speed (R .P .M .) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2,500
Air inlet (N .P .T .) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/4
Hose size (I .D .) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3/8 in .
Length (IN .) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 .5
Weight (LBS .) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 .6
Specifications are subject to change without notice .
WARNING!
READ, UNDERSTAND AND FOLLOW ALL INSTRUCTIONS AND
WARNINGS BEFORE OPERATING THIS TOOL . FAILURE TO DO SO
MAY RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE
AND WILL VOID WARRANTY .
PARTS LIST
NO. DESCRIPTION QTY NO. DESCRIPTION QTY NO. DESCRIPTION QTY
INSuFFICIENT POWER:
Probable Cause
Solution
Dirty or clogged air passages . . . . . . . . . . . . . . . . . .Flush and lubricate tool, drain air tank and supply line
Insufficient air supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Increase line pressure, Make sure compressor
matches tool's air pressure and consumption needs
Air leakage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Use PTFE tape at all fittings and joints . Check tool for
worn or damaged O-rings & seals .
Worn/damaged wear & tear parts . . . . . . . . . . . .Replace as necessary .
Tool matching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Be sure you are using a tool suited for the torque
requirements of the job at hand .
TROUBLESHOOTING