SOFTWARE VERSION
The software display cannot be altered and is just for your reference. You can only view
the software version in DAB, FM or Bluetooth mode.
1. Press the
ON/OFF button
to switch on the radio.
2. Press the
SOURCE button
to select FM or DAB, or Bluetooth mode.
3. Press the
MENU button
until the display shows “Full Scan” at DAB, or "Scan
setting" at FM, or "Disconnect BT" at Bluetooth mode, and then rotate the
TUNING/
SEEK knob
until the display shows “System”.
4. Press the
TUNING/SEEK knob
; rotate the
TUNING/SEEK knob
until the display
shows “SW version”.
5. Press the
TUNING/SEEK knob
to view the software version.
6. Press the
TUNING/SEEK knob
back to the last menu, and press the
TUNING/
SEEK knob
again to return to the normal radio display.
Notes:
USB socket inside battery compartment is for upgrading the software of the
device.
SYSTEM RESET
If the radio fails to operate correctly, or some digits on the display are missing or
incomplete, carry out the following procedure.
1. Press the
ON/OFF button
to switch on the radio.
2. Press the
MENU button
,
3. Rotate the
TUNING/SEEK knob
until the display shows “System”. Press the
TUNING/SEEK knob
.
4. Rotate the
TUNING/SEEK knob
until the display shows “Factory reset”. Press the
TUNING/SEEK knob
.
5. Rotate the
TUNING/SEEK knob
to select between “Yes” or “No”.
Select “Yes” if you wish to reset the radio; otherwise, select “No” to cancel the
selection.
6. Press the
TUNING/SEEK knob
to cause the factory reset.
7. A full reset will be performed. All presets and the station list will be erased. All
settings will be set to the default values.
The display will show “WELCOME TO DIGITAL RADIO” for a few seconds, and
then the radio will automatically perform an auto scan of the Band III DAB channels
and the FM band.
In case of malfunction due to electrostatic discharge; reset the product as above to
resume normal operation. If you are not able to perform the reset operation as above,
remove and reconnect the power supply.
BACKLIGHT
LCD backlight configuration
1. Press the
ON/OFF button
to turn on the radio.
2. Press the
MENU button
, and then rotate the
TUNING/SEEK knob
until the display
shows “System”.
3. Press the
TUNING/SEEK knob
; rotate the
TUNING/SEEK knob
until the display
shows “LCD backlight”.
4. Press the
TUNING/SEEK knob
to enter the LCD backlight adjustment menu.
5. Rotate the
TUNING/SEEK knob
to select “on” in order to keep backlight always
lightened when the radio is turned on with AC power supply;
6. Or rotate the
TUNING/SEEK knob
to select “off” (by default) so that the backlight
will be lightened for about 10 seconds whenever a button is pressed with AC power
supply.
7. Press the
TUNING/SEEK knob
to confirm your choice.
Note: The LCD backlight option “on” is only functional when the radio is powered by AC
power supply. When the radio is powered by battery power supply, the LCD backlight
is switched to option “off” – 10 seconds lightened when a button is pressed. When the
radio is connected to mains AC power again, the last user setting will be applied again.
BLUETOOTH LED
Bluetooth LED configuration
Press the
ON/OFF button
to turn on the radio.
Press the
MENU button
, and then rotate the
TUNING/SEEK knob
until the display
shows “System”.
Press the
TUNING/SEEK knob
; rotate the
TUNING/SEEK knob
until the display shows
“Bluetooth LED”.
Press the
TUNING/SEEK knob
to enter the Bluetooth LED adjustment menu.
Rotate the
TUNING/SEEK knob
to select “on” in order to keep backlight always
lightened when the radio is turned on with AC power supply;
Or rotate the
TUNING/SEEK knob
to select “off” (by default) so that the backlight will be
lightened for about 10 seconds whenever a button is pressed with AC power supply.
Press the
TUNING/SEEK knob
to confirm your choice.
Note: The Bluetooth LED option “on” is only functional when the radio is in Bluetooth
mode. If the Bluetooth LED option is set to “off”, this blue LED will be turned off either
mobile phone is connected (not blinking) or not connected (blinking).
GB
24
23
