background image

TONE

The 

Tone

 function enables the user to adjust the lower and higher sound frequencies.

1.  Press the ON

 / OFF button to turn on the radio.

2.  Press and hold the 

VOLUME/TONE knob

 for about 3 seconds, the display shows  

 

“BASS 0”.

3.  Rotate the 

VOLUME/TONE knob

 to set the desired Bass level.

4.  Press the 

VOLUME/TONE knob

 to confirm, the display shows “TREBLE 0”.

5.  Rotate the 

VOLUME/TONE knob

 to set the desired Treble level.

6.  Press the 

VOLUME/TONE knob

 to confirm and return to normal display.

LANGUAGE SETTING

The radio can be configured to a different language.

1.  Press the 

ON/OFF button

 to turn on the radio.

2.  Press the 

MENU button

, and then rotate the 

TUNING/SEEK knob

 until the display  

 

shows “System”.

3.  Press the 

TUNING/SEEK knob

; rotate the 

TUNING/SEEK knob

 until the display  

 

shows “Language”.

4.  Press the 

TUNING/SEEK knob

 to enter the language adjustment menu.

5.  Rotate the 

TUNING/SEEK knob

 until the desired language appears on the display  

 

(default is English).

6.  Press the 

TUNING/SEEK knob

 to confirm your choice. The display will change to  

 

the chosen language.

SOFTWARE VERSION

The software display cannot be altered and is just for your reference. You can only view 

the software version in DAB, FM or Bluetooth mode.

1.  Press the 

ON/OFF button

 to switch on the radio.

2.  Press the 

SOURCE button

 to select FM or DAB, or Bluetooth mode. 

3.  Press the 

MENU button

 until the display shows “Full Scan” at DAB, or "Scan  

 

setting" at FM, or "Disconnect BT" at Bluetooth mode, and then rotate the 

TUNING/ 

 

SEEK knob

 until the display shows “System”.

4.  Press the 

TUNING/SEEK knob

; rotate the 

TUNING/SEEK knob

 until the display  

 

shows “SW version”.

5.  Press the 

TUNING/SEEK knob

 to view the software version.

6.  Press the 

TUNING/SEEK knob

 back to the last menu, and press the 

TUNING/ 

 

SEEK knob

 again to return to the normal radio display.

Notes: USB socket inside battery compartment is for upgrading the software of the 

device.

SYSTEM RESET

If the radio fails to operate correctly, or some digits on the display are missing or 

incomplete, carry out the following procedure.

1.  Press the 

ON/OFF button

 to switch on the radio.

2.  Press the 

MENU button

3.  Rotate the 

TUNING/SEEK knob

 until the display shows “System”. Press the   

 

TUNING/SEEK knob

4.  Rotate the 

TUNING/SEEK knob

 until the display shows “Factory reset”. Press the  

 

TUNING/SEEK knob

.

5.  Rotate the 

TUNING/SEEK knob

 to select between “Yes” or “No”. 

6.  Select “Yes” if you wish to reset the radio; otherwise, select “No” to cancel the  

 selection.

7.  Press the 

TUNING/SEEK knob

 to cause the factory reset.

8.  A full reset will be performed. All presets and the station list will be erased. All  

 

settings will be set to the default values. 

The display will show “WELCOME TO DIGITAL RADIO” for a few seconds, and then the 

radio will automatically perform an auto scan of the Band III DAB channels and the FM 

band.

In case of malfunction due to electrostatic discharge; reset the product as above to 

resume normal operation. If you are not able to perform the reset operation as above, 

remove and reconnect the power supply.

BACKLIGHT

LCD backlight configuration

1.  Press the 

ON/OFF button

 to turn on the radio.

2.  Press the 

MENU button

, and then rotate the 

TUNING/SEEK knob

 until the display  

 

shows “System”.

3.  Press the 

TUNING/SEEK knob

; rotate the 

TUNING/SEEK knob

 until the display  

 

shows “LCD backlight”.

4.  Press the 

TUNING/SEEK knob

 to enter the LCD backlight adjustment menu.

5.  Rotate the 

TUNING/SEEK knob

 to select “on” in order to keep backlight always  

 

lightened when the radio is turned on with AC power supply;

6.  Or rotate the 

TUNING/SEEK knob

 to select “off” (by default) so that the backlight  

 

will be lightened for about 10 seconds whenever a button is pressed with AC power  

 supply.

7.  Press the 

TUNING/SEEK knob

 to confirm your choice.

Note: The LCD backlight option “on” is only functional when the radio is powered by AC 

power supply. When the radio is powered by battery power supply, the LCD backlight 

is switched to option “off” – 10 seconds lightened when a button is pressed. When the 

radio is connected to mains AC power again, the last user setting will be applied again.

GB

18

17

Summary of Contents for SLIM-2













Reviews: