background image

8

TIMER: AUTO START/

STOP FEATURE:

Press Timer
button

DO THIS:

AIR CONDITIONER FEATURES(CONTINUED)

CHECK FILTER FEATURE:

Press Check
Filter button

DO THIS:

Energy

Saver

on

off

Timer

Auto

Fan

Cool

Dry

Mode

TEMP/TIMER

TEMP/TIMER

Sleep

Check

Filter

Follow 

Me

Auto

On/off

Fan

High

Med 

Low

on

off

Timer

TEMP/TIMER

TEMP/TIMER

Clean

Air

 This feature is a reminder to clean the Air Filter for
 more efficient operation. The LED(light) will illumi-
 nate after 250 hours of operation. To reset after 
 cleaning the filter, press the Check Filter button and
 the light will go off.

NOTE:

NOTE:

 -   When the unit is on or off, first press the Timer button, 
     the TIMER ON indicator light illuminates. It indicates 
     the Auto Start program is initiated. 
 -   When the time of TIMER ON is displayed

 -   Press or hold the UP or DOWN button to change the 
     Auto time by 0.5 hour increments, up to 10 hours,then
     at 1 hour increments up to 24 hours. The control will 
     count down the time remaining until start. 
 -   The selected time will register for 5 seconds, and the 
     system will automatically revert back to display the 
     previous temperature setting or room temperature when 
     the unit is on.(When the unit is off,there is no display.)
 -   Turning the unit ON or OFF at any time or adjusting 
     the timer setting to 0.0 will cancel the Auto Start/Stop 
     timed program.
 

,press the 

     Timer button again, the TIMER OFF indicator light 
      illuminates. It indicates the Auto Stop program is 
      initiated. 

O

O

Shows the set temperature in    C  or    F  and the
Auto-timer settings.While on Fan only mode,it shows 
the room temperature.

DISPLAYS:

      -

Evaporator temperature sensor error-Unplug the 

       unit and plug it back in. If error repeats, call for 
       service.
       NOTE:       is displayed as shown in the left picture. 

HS -

Electric heating sensor error-Unplug the unit and

        plug it back in. If error repeats, call for service.
        

   Error codes:
AS-

Room temperature sensor error-Unplug the unit 

       and plug it back in. If error repeats, call for service.
       NOTE: In Fan only mode, it will display LO  or  HI .

Energy

Saver

on

off

Timer

Auto

Fan

Cool

Dry

Mode

TEMP/TIMER

TEMP/TIMER

Displays

DISPLAYS:

Summary of Contents for 12.000 BTU




























Reviews: