background image

Assembly & Operation Manual

 

Modification 

TTR-10AT

TTR-10AK

, 1 box in each: 

Transportation box dimensions (L×H×W)  ................................................................... 104×40×32cm 
Transportation box weight (gross)  .....................................................................................  max 58kg 

Modification 

TTR-10AB

, 2 boxes: 

Transportation box #1 dimensions (L×H×W)  .............................................................. 104×40×32cm 
Transportation box #1 weight (gross)  ................................................................................  max 53kg 
Transportation box #2 dimensions (L×H×W)  .............................................................. 115×40×22cm 
Transportation box #2 weight (gross)  ................................................................................  max 33kg 

7  SAFETY REQUIREMENTS 

7.1  Installation safety requirements 

The turnstile installation must be carried out by specialists who have fully studied this manual and 
passed safety training, in accordance with the general rules for the implementation of electrical and 
installation work. 

 

Warning! 

  The power source or battery must be turned off and unplugged during installation of the 

turnstile. 

  Only serviceable tools must be used for installation. 

  Lay the cables in compliance with the electrical installations rules of operation. 

  Before turning on the turnstile for the first time, make sure it's installed and connected 

correctly. 

Power supply unit installation must be made in accordance with the safety rules given in its 
certificate. 

7.2  Operation safety requirements 

Follow general electrical safety rules when operating the turnstile. 

 

It is prohibited! 

  Do not use the turnstile under conditions that do not comply with the requirements of 

Section 2 of this Manual. 

  Do not use the turnstile at supply voltage that does not comply with the requirements of 

Section 3 of the Manual. 

The power supply unit should be used in compliance with its operational documentation. 

8  INSTALLATION INSTRUCTIONS 

Follow the safety requirements during the installation (Sect. 7.1). 

 

Warning! 

The manufacturer is not responsible for any damage to the turnstile or other equipment, as 
well as other damages caused by improper installation, and rejects any consumer 
complaints if the installation is performed in violation of the instructions given in this 
manual. 

8.1  Installation details 

The turnstile installation is a demanding operation, both performance and service life of the product 
largely depend on it. Installation must be carried out by at least two specialists qualified as an 
installer and an electrician. It is recommended to study this section carefully prior to installation, 
and follow the given instructions. 

Installation surface recommendations:  

The turnstile can be mounted on the cylindrical racks (vertical pipes) of the vehicle using the 

MT10.1

 bracket (for 

TTR-10AT

 modification), or on a strong vertical wall with the 

MT10.2

 bracket 

(for 

TTR-10AK

 modification), or on a concrete floor using the 

MT10.3

 mounting post (for  

TTR-10AB

 modification). 

18 

Summary of Contents for TTR-10A Series



































Reviews:

Related manuals for TTR-10A Series