background image

Assembly and Operation Manual 

18 

Card captured

” shows that the card has not fallen into card container. The reason can be 

blocking of card container, card capture reader failure or if the card was not inserted into 
the slot. 

 

Attention! 

If the passage was not authorized the visitor shall take the card out of the slot and 
refer to the entrance operator. 

10.2  Presenting a permanent card 

The permanent card is presented to the top cover of the card capture reader. 

At the permanent card presentation, considering that card is operative and its validity 
corresponds to the time of passage, the ACS controller sends a signal to unblock the 
operating device. It is recommended to switch on the green indicator on the indication 
module at that showing authorization of passage. After that the ACS controller blocks the 
operating device and switches back to the standby mode  

In case of the ban on passage (card fault, card invalidity corresponding to the time of 
passage or access wrights) it is recommended to switch on for 2 sec. the red indicator and 
sound signal on the indication module at that. The ACS controller switches back to the 
standby mode after that. 

10.3  Blocking and resume of card capturing 

On cards capturing the container gets full. When it is full further cards capturing is blocked 
till the captured cards are extracted from the container. In this case the card capture 
reader generates the 

“Fault” 

signal for the ACS controller. 

At blocking of the guest card capturing it is recommended to set up the following indication 
on the indication module: at first blinking of the green and red indicators, after that switch 
on for 2 sec. the red indicator and sound signal. The ACS controller switches back to the 
standby mode after that. 

 

Note: 

While the capturing of guest cards is blocked the permanent cards are operated in 
normal order. 

To resume capturing of guest cards it is necessary to extract the full container (9) from the 
card capture reader and empty the cards  (the order of the container extraction and 
installation is described in Clause 10.4. 

If the container is free from cards but the card capture reader is still blocked a likely reason 
for this could be failure of the card capture reader units. It is recommended to apply to the 
PERCo Technical Support Department. 

10.4  Removal and installation of the card container 

To take out the card container (9) from the card capture reader proceed as follows: 

1  Switch off the power supply of the card capture reader. 
2  Insert the key into the lock (8). 
3  Turn the key all the way (open the lock). 
4  Tilt the card container in the front direction. 
5  Lift the container and take it away. 

To insert the card container into the card capture reader proceed as follows: 

Summary of Contents for IC-03.1























Reviews: