background image

Model 52791 Getting Started Guide

Page 5

Rev.  1.0

Before You Begin:

 Jumper and Switch Settings

As shipped from the factory, all jumpers and switches are set in default positions on the 

Pentek Model 52791. The default operating parameters they select may or may not meet 

your requirements. Therefore, consider the following before installation:

Pentek Model 71791 XMC Module Switch SW1 

 FPGA Configuration

When you install Model 52791, you may need to set DIP switch 

SW1 

on the 71791 XMC 

module (which controls FPGA configuration) based on the characteristics of your host 

bus. Therefore, you will need to consider the following before you begin installation:

• FLASH  memory  write  protect/write enable 
• PLX PCIe switch maximum speed select
• Select boot configuration at power on
• PCIe clock select
• P16 clock select
• JTAG source select
• GateXpress

®

 disable (GateXpress is the FPGA

PCIe configuration manager for 

loading and reloading the FPGA)

For example, Switch 

SW1

2

 allows you to change the maximum speed of the PLX PCIe 

switch from Gen 3 (the factory default) to Gen 2. 

NOTE:

The Model 71791 XMC module is shipped to boot with the Gen 3 x8 PCIe 
default FPGA code. The Model 5201 VPX carrier limits the default of the 
Model 52791 to Gen 3 x4.

To preview the DIP switch settings you’ll need to make, refer to Section 2.4 of the 

Model 

52791 Installation Manual

.

Pentek Model 5201 VPX Carrier Jumpers

XMC JTAG: 

Jumper block 

JB1

 includes or bypasses the 71791 XMC as part of the 

JTAG chain from the Pentek JTAG connector (

J5

).

XMC Reset Source

: Jumper block 

JB3

 selects the source of the reset signal sent to the 

XMC interface (VPX SYSRESET or Board Power On).

XMC MVMRO

: Jumper block 

JB4

 enables/disables MVMRO (XMC Write Prohibit) 

for the XMC interface.

To preview the jumper settings you’ll need to consider for the 5201 carrier PCB, refer to 

Section 2.6 of the 

Model 52791 Installation Manual.

 

NOTE:

To access all jumpers, you must remove the XMC module from the VPX 
carrier, as described in Section 2.3 of the 

Model 52791 Installation Manual

.

Summary of Contents for 52791















Reviews: