PENTA 1130 Operator'S Manual Download Page 13 | Manualshive

Page: 13 / 30

PENTA 1130 Operator'S Manual Download Page 13

13

Tractor Requirements

EQUIPMENT MATCHING

The PENTA TMR Cutter-Mixer-Feeder trailer model is designed to be used with Agricultural
tractors. To ensure a good performance, the following recommendations regarding minimum
equipment size and horse-power should be met.

A loaded machine may weigh as much as 10,000 kg, or 22,000 lbs. An operator must use his own
discretion when determining whether the tractor attached is suitable for the terrain. Using a
small tractor on a heavy piece of machinery can cause severe injury or death if the operator loses
control of the machinery.

Never leave the mixer parked full. Staring up a mixer that has been stopped for more than ½ an
hour can greatly increase the start up horse power. And damage the drive train.

Mixer Series

Horsepower

3030

40-70HP

4130

50-80HP

5030

50-80HP

5930

50-120HP

4430

60-90HP

6730

80-130HP

8030

130-160HP

9630

135-170HP

1130

140 -180HP

1430

150-200HP

1030

90-180HP

1730

200-250HP

«
...
11
12
13
14
15
...
»

Summary of Contents for 1130































Reviews:

No comments