Penn Photoreactor m2 User Manual Download Page 4

 

 

 

The Illuminator unit requires adequate airflow to 
maintain proper cooling. Ensure the ventilation holes 
and bottom of the unit are unobstructed and a 

minimum of 4” clearance is provide

d in rear of unit.

 

 

 

If the Illuminator is used in a manner not specified 
within this manual, the protection provided by the 
equipment  might  be  impaired.  It  is  the 
responsibility  of  the  user  to  follow  all  applicable 
safety guidelines in prevention of injury or damage 
to the unit. 

 

 

Use  of  the  equipment  with  an  unapproved  power 
supply may cause damage to the device and/or power 
supply and may result in injury. 

 

 

It is the responsibility of the user to assess and mitigate 
any  hazards  that  may  result  from  a  mixing 
interruption. 

 

 

It is the responsibility of the user to assess and mitigate 
any  hazards  that  may  result  from  mixing  volatile  or 
flammable  materials.    Users  shall  comply  with  all 
applicable  safety  and  accident-prevention  procedures 
for laboratory work. 

 

 

Device  intended  for  a  variety  of  chemical  reactions; 
Device to be used by trained operator in a laboratory 
setting. 

 

 

Operation  of  multiple  devices  simultaneously  in  a 
single enclosed area may require ear protection 

 

 

Explanation of labels 

 

 

Manufacturer. 

 

Caution 

 Read User Manual. 

 

Summary of Contents for Photoreactor m2















Reviews: