background image

PelPro Pellet Stove  •  8104-171B  •  10/21

PelPro Pellet Stove  •  8104-171B  •  10/21

pelprostoves.com

pelprostoves.com

38

39

Reference Materials

Listing and Code 

Approvals

Listings and Certifications

Warranty

1

04/21

7014-328B

Components Covered

Warranty Period

(Parts only, Labor not included)

Electrical

1 Year

Steel Parts (excluding fi re pot)

5 Years

All replacement parts are covered for remainder of original warranty period or 

90 days, whichever is longer

90 Days

Hearth & Home Technologies, Inc. -  PelPro Limited Warranty

Hearth & Home Technologies, Inc. (HHT), on behalf of its PelPro brand, extends the following warranty for PelPro 

Stoves purchased from an authorized retailer.
If you experience issues with your PelPro Stove, Consumer Care is available to assist you with troubleshooting 

technical issues.
This warranty covers components of the PelPro Stoves as listed in the table below.

Warranty Coverage:

Subject to the table below, HHT warrants to the owner of the PelPro Stove that the Stove will be free from defects 

in materials and workmanship at the time of manufacture. After installation, if covered components are found to be 

defective in materials or workmanship during the applicable warranty period, HHT will replace the covered components.
HHT, at its own discretion, may fully discharge all of its obligations under such warranties by replacing the product itself 

or refunding the verifi ed purchase price of the product itself. The maximum amount recoverable under this warranty 

is limited to the purchase price of the product. This warranty is subject to conditions, exclusions, and limitations as 

described below.

Warranty Period:

Warranty coverage begins on the date of original purchase. The warranty period for covered components is as follows:

Parts Service & Returns:

HHT is proud to off er the best technical and sales support in the industry. If you have any questions about how to 

operate your Stove or if you need service parts, please visit PelProstoves.com.

Warranty Exclusions:

Warranty does not cover damage or breakage due to misuse, improper handling or modifi cations. There is no warranty 

on the paint, glass, fi re pot, fi re brick, or any gaskets, or against damage caused from corrosion. There is no expressed 

or implied performance warranty on PelPro units as HHT has no control over the installation, operation, cleaning, 

maintenance, or type of fuel burned.

Some states do not allow exclusion or limitation of incidental or consequential damages, or limitations of implied 

warranties, so the limitations or exclusions set forth in this limited warranty may not apply to you. This limited warranty 

gives you specifi c legal rights and you may have other rights, which vary from state to state. Warranty is void if the 

PelPro Stove has not been installed, operated, cleaned and maintained in strict accordance with HHT’s instructions.
NEITHER HHT NOR THE RETAILER FROM WHO YOU PURCHASED YOUR PELPRO UNIT SHALL BE 

RESPONSIBLE, LEGALLY OR OTHERWISE, FOR THE INCIDENTAL OR CONSEQUENTIAL DAMAGE TO 

PROPERTY OR PERSONS RESULTING FROM THE USE OF THIS PRODUCT. ANY WARRANTY IMPLIED BY LAW, 

INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF THE MERCHANTABILITY OR FITNESS, SHALL BE 

LIMITED TO ONE (1) YEAR ON THE BREACH OF THIS WARRANTY OR ANY TYPE OF WARRANTY EXPRESSED 

OR IMPLIED BY LAW. HHT SHALL IN NO EVENT BE LIABLE FOR ANY SPECIAL, INDIRECT, CONSEQUENTIAL 

OR OTHER DAMAGES OF ANY NATURE WHATSOEVER IN EXCESS OF THE ORIGINAL PURCHASE PRICE 

OF THIS PRODUCT. ALL WARRANTIES BY HHT ARE SET FORTH HEREIN AND NO CLAIM SHALL BE MADE 

AGAINST HHT ON ANY ORAL WARRANTY OR REPRESENTATION.

Reference Materials

Service Part List

Service Parts

Beginning Manufacturing Date: Aug 2021  

Ending Manufacturing Date: Active

PP150

IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement parts for 

your appliance please provide model number and serial number. All parts listed in this manual must 

be ordered from a dealer.

Stocked 

at Depot

ITEM

DESCRIPTION

COMMENTS

PART NUMBER

1

Hopper Lid Assembly

SRV7086-019

Hopper Extension

PPHE200

Handle, Hopper Lid

SRV200-0110

2

Side Curtain, Left Hand

SRV8104-154

Y

3

Exhaust Combustion Blower

812-4400

Y

Gasket, Between Blower Housing and Stove

SRV240-0812

Y

Gasket, Between Blower Housing and Motor

812-4710

Y

4

Snap disc, Manual Reset

SRV230-0080

Y

5

Door Assembly

SRV7086-021

Y

6

Baffle Kit

SRV7077-006

7

Firepot

SRV7077-003

Y

8

Igniter Chamber Kit

SRV7077-110

9

Igniter Kit

SRV7000-660

Y

10

Control Board

SRV7104-050

Y

11

Convection Blower

KS-5020-1052

Y

Convection Blower Gasket

SRV7081-195

Convection Blower Bracket

SRV7081-210

12

Vacuum Switch

SRV7000-531

Y

Vacuum Hose, 5/32 ID

3 Ft

SRV240-0450

Y

Hose, Barb Assembly

SRV229-0920

13

Side Curtain, Right Hand

SRV8104-153

Y

14

Dial Control

SRV7083-036

Y

Wire Harness, Dial Control

SRV7000-667

Y

15

Hopper Switch

SRV7000-612

Y

See Following page for additional servcie parts

6/21

Pellet Stove

1

2

10

11

3

4

5

6

9

8

7

12

13

14

15

16

Summary of Contents for PP150
























Reviews: