PelPro Pellet Stove • 8104-171B • 10/21
PelPro Pellet Stove • 8104-171B • 10/21
26
27
Replacement Parts
Replacement Parts
1
Zone
1
Zone
2
Zone
2
Zone
3
Zone
3
Zone
Convection Blower
1.
Turn the dial control to the off position. Unplug the
power to the unit.
2. Remove the right side panel by loosening the three
screws attaching it to the back of the appliance.
3. Using a 7/16 wrench or socket, remove the 2 nuts
holding the blower to the convection plenum
4. Lower the back of the blower and lift out.
5. With the blower removed, unplug its wires from the
wire harness.
6. Remove the screws holding the retainer plate to the
convection blower housing.
7. To replace, put the bottom lip of the blower into
the lower slot. Attach the top of the blower to nuts.
Reattach the metal plate and screw nuts into bolts.
8. Attach wires to wire harness.
9. Attach the right side panel and tighten screws.
Replacement kit: KS-5020-1052
Exhaust Blower
1.
Turn the dial control to the off position. Unplug the power to the unit.
2. Remove the left side panel by loosening the three screws attaching it to the back of the
appliance.
3. Disconnect 2 white wires from the blue wires of the exhaust blower.
4. Remove the blower motor attached to a removable plate on the exhaust blower.
Depending on the model, use a 1/4 inch socket, or 1/4 inch Nut Driver or #2 Phillips Head
screw driver to loosen the 6 screws in the keyhole shaped holes and rotate the plate. It is
only necessary to loosen screws.
5. Remove the exhaust blower and gasket.
6. Check for degradation on the gasket and replace if necessary using the gasket included in
the kit.
7. Re-install in reverse order.
Replacement kit: 812-4400
Replacement Parts
Zone 3 - Back of Stove
Replacement Parts
1
Zone
1
Zone
2
Zone
2
Zone
3
Zone
3
Zone
Snap Disc
1.
Turn the dial control to the off position. Unplug the
power to the unit.
2. Using #2 Phillips screwdriver, loosen the bolts on the
rear of the unit holding on the left side panel. You do
not need to remove the screws. Remove side panel
by lifting up and out.
3. Locate the snap disk on the top side of the feed tube
where it meets the hopper. Disconnect the wire leads
from the snap disk.
4. Using a #1 Phillips screwdriver, remove two 6-32
fasteners retaining the snap disk onto the side of the
feed tube.
5. Using the same fasteners, attach the new snap disk.
Attach the wire leads.
6. Restore power.
Replacement kit: SRV230-0080
Igniter
1.
Turn the dial control to the off position. Unplug the power to the unit.
2. Remove the right side panel & unplug the wire leads to the igniter.
3. Remove the screw in the top of the igniter chamber. Pinch the ends of the bracket together
and pull the igniter straight out of the igniter chamber.
4.
If there is difficulty in removing the igniter from the chamber, the chamber can be removed
from the rear of the firebox by removing the 1/4-20 bolt using 3/8” socket.
5. Re-install the new igniter into the chamber using the bracket. Reattach wires to terminals.
6.
Inspect the igniter from the front of the unit by removing the firepot and looking into the end
of the chamber. MAKE SURE THE IGNITER IS CENTERED IN THE CHAMBER.
Replacement kit: SRV7000-660
