Pella 81AK0101 Installation Instructions Manual Download | Manualshive

Page: 18 / 18

background image

TROUBLESHOOTING - Adjustable Strike Latching Issues

TABS

Adjustable strike shim

(side view)

Strike

(front view)

Adj. Strike Shim

(end view)

Factory

installed

side

Side to be

used in

Issue 2

Issue 2:

Door needs to close

more tightly against

the weather-strip.

Remove the strike

and adjustable

strike shim. Remove

the tabs from the

adjustable strike

shim and install

so that the thicker

side is visible at

the strike edge.

Reinstall the strike.

Issue 1:

Door is difficult

to latch.

Remove

the strike and

adjustable

strike shim then

reinstall the

strike.

«
...
16
17
18

Summary of Contents for 81AK0101



















Reviews:

No comments

Related manuals for 81AK0101

Brand: Waferlock Pages: 3

Brand: Black & Decker Pages: 3

PEMKO LP200 Series

Brand: Assa Abloy Pages: 2

Ultraloq U-Bolt WiFi

Brand: U-tec Pages: 38

Code Cylinder 1101

Brand: MYLOQ Pages: 8

Brand: Borglocks Pages: 2

BL6100Mk4 Series

Brand: Borg Locks Pages: 4

Brand: Corporate Locksmiths Pages: 9

Brand: Yale Pages: 36

Brand: Häfele Pages: 10

Brand: Maco Pages: 7

Brand: CAME Pages: 12

Magnetic Catch 327

Brand: Ives Pages: 1

Brand: Weiser Pages: 8

AElement Fusion

Brand: Salto Pages: 2

Brand: PORT Pages: 22

Brand: PORT Pages: 26

Brand: Bewator Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands