background image

E. 

Apply sill flashing tape #1.

#UTAPIECEOFmASHINGTAPELONGER

than the opening width. Apply at the bottom of the opening as shown 

% SOITOVERHANGSTOTHEEXTERIOR

Note: The tape is cut 12" longer than the width so that it will 
extend 6" up each side of the opening.

2

 WINDOW PREPARATION

A. 

Remove plastic wrap and cardboard packaging

 from window. DO NOT remove plastic 

shipping spacers located between the window sash and frame. The shipping spacers will 
help keep the window square during installation. DO NOT unlock or open the window 
until it is fully fastened.

Note: If screens, grilles or hardware are removed from the window 
at this time, label them and store them in a protected area.

2C

B. 

Designer units with half screen only:

 

 1. 

Remove the screen from the window.

&ROMTHEEXTERIOR

pull one side of the screen near the shipping clips until the 
clips disengage from the window. 

Rotate the screen shipping clips

TOWARDTHEEXTERIOROFTHE

screen (in the direction of the arrows) until they snap free 
from the screen.

 3. 

Set the screen aside

 in a safe location.

 4. 

Discard the screen shipping clips.

F. 

Tab the sill flashing tape and fold.

 Cut 1" wide tabs at each corner 

FROMEACHSIDEOFCORNER & &OLDTAPETOTHEEXTERIORAND
PRESSlRMLYTOADHEREITTOTHEWATERRESISTIVEBARRIER

C. 

Fold out installation fin to 90°.

 Be careful not to remove or 

TEARTHElNCORNERS

Note: If the fin is not at 90

°

, the window will not line up 

correctly on the interior.

'

Apply sill flashing tape #2.

#UTAPIECEOFmASHINGTAPELONGER

than the opening width. Apply at the bottom, overlapping tape #1 by 

ATLEAST$ONOTALLOWTHETAPETOEXTENDPASTTHEINTERIORFACEOF
THEFRAMING'

Note: The flashing tape may not fully cover the framing members.

(

Install and level sill spacers.

 Place 1" wide by 3/8" thick spacers on 

THEBOTTOMOFTHEWINDOWOPENINGFROMEACHSIDE3PACERSARE

also required at points where windows are joined in multiple window 
applications. Add shims as necessary to ensure the spacers are level. 
Once level, attach spacers and shims to prevent movement.

Note: Improper placement of shims or spacers may result in 
bowing the bottom of the window.

£

TWO OR MORE PEOPLE WILL BE REQUIRED  

FOR THE FOLLOWING STEPS.

%*4$"3%

164)

%*4$"3%

164)

4IJQQJOH

$MJQ

Ó Ó

Ó £

1VMMTDSFFOOFBS

TIJQQJOHDMJQ

£

£

£

1

 ROUGH OPENING PREPARATION (continued)

Summary of Contents for 802X0104









Reviews: