- 8 -
MECHANISMS.
_ BE CAREFUL NOT TO HURT THE CHILD
WHEN ADJUSTING THE MECHANISMS
(BACKREST).
_ IT MAY BE DANGEROUS TO USE
ACCESSORIES NOT APPROVED BY THE
MANUFACTURER.
INSTRUCTIONS
1 OPENING: To open the baby rocker, rotate the tubes
forward until they click into place.
2 ADJUSTING THE BACKREST: The backrest can be set in
3 different positions. Rotate lever 1 outwards (leaving
it in the open position) (fig_a), rotate lever 2 outwards
and at the same time adjust the backrest (fig_b). Once
in the selected position, remember to close lever 1
again.
3 ADJUSTING THE REAR LEDGE: the rear ledge can be
set at two different heights. To raise it, pull the two
levers outwards from both sides and at the same
time push the tabs upwards (fig_a). Rear ledge raised
(fig_b).
4 SAFETY BELT: thread the safety belt through the
crotch strap and engage the buckle until it clicks
(fig_a). To release the safety belt, press the two sides
of the buckle and simultaneously pull the waist strap
outwards (fig_b).
5 STAND: the base of the baby rocker can be rocking
(fig_a) or stable. To stop it from rocking, rotate the
stabilizer stand outwards (fig_b).
6 TRANSPORT: The baby rocker has carrying straps on
the sides.
7 FOLDING UP: To fold up the baby rocker (fig_a), move
the backrest to the lowest position, then press button
A simultaneously on both sides and rotate the frame
as shown in the figure. Before moving the folded up
baby rocker, put the elastic loop around the fastener
(fig_b). When folded up, the baby rocker is extremely
compact and takes up very little space (fig_c).
8 REMOVABLE COVERS: To remove the covers of the
baby rocker, unfasten the Velcro (fig_a) and pull off
the fabric covering from the front (fig_b).
9 Slip the cover side loop off the frame tubes (fig_a),
unbutton the back of the backrest (fig_b) and slide
the cover upwards (fig_c). Important: when re-
covering the baby rocker remember to insert the loop
onto the tubular frame.
CLEANING AND MAINTENANCE
PRODUCT MAINTENANCE: protect from the weather:
water, rain, or snow; prolonged and continuous
exposure to bright sunlight may give rise to colour
changes of various different materials; store this
product in a dry place.
CLEANING THE CHASSIS: periodically clean all plastic
parts with a damp cloth. Do not use solvent or
similar cleaning products; keep all metal parts dry to
prevent rusting; keep moving parts clean (adjustment
mechanisms, locking mechanisms) and free of dust
and sand and, if necessary, lubricate with light
machine oil.
CLEANING FABRIC PARTS: brush fabric parts to
remove dust and wash by hand at a maximum
temperature of 30°C; do not wring; do not use
chlorine bleach, do not iron; do not dry clean; do not
apply solvent-based stain removers and do not dry in
a tumble dryer.
PEG-PÉREGO S.p.A.
Peg-Pérego S.p.A. is an ISO 9001
certified company. This certification is a
guarantee for customers and
consumers of the transparency and
trustworthiness of the company's
procedures and working methods.
Peg Pérego can make changes at any time to the
models described in this publication for technical or
commercial reasons.
Peg Pérego is at the disposal of its customers and
consumers to ensure that all their demands and
queries are fully satisfied. It is a key part of our policy
to ensure we are always aware of our customers'
views and requirements. We would therefore be very
grateful if, after using a Peg Pérego product, you
take the time to fill in our CUSTOMER SATISFACTION
QUESTIONNAIRE, making a note of any comments
or suggestions you might have. You can find the
questionnaire on the Peg Pérego website: www.
pegperego.com
PEG-PÉREGO AFTER-SALES SERVICE
If any parts of your Peg Pérego product should be
accidentally mislaid or damaged, use exclusively
genuine original Peg Pérego replacements. For any
repairs, replacements, product information, and
orders for genuine original replacement parts and
accessories, contact Peg Pérego After-Sales Service:
tel.
0039/039/60.88.213
fax
0039/039/33.09.992
website
www.
pegperego.com
