remove the padded cushion, unthread the crotch strap.
10
•
The safety seat handle has four fixed positions. To rotate it press
the two round buttons on the handle and simultaneously
move it to the required angle. Ensure it clicks into position.
•
Position A
: the in-car position;
Position B
: the position for
transport by hand and for attachment to a base, stroller or
chassis; Position C
: allows the safety seat to rock;
Position D
:
stops the safety seat from rocking.
11
• To fit the hood, insert the hood attachments into the slots
on the safety seat and arrange the rear part of the hood
behind the backrest.
12
•
The hood has two positions. To raise or lower the hood push it
back or pull it forward. To remove the hood, press the buttons
on its attachment points and at the same time lift it upwards.
• IMPORTANT: the hood must not be used to lift the safety
seat because it might detach.
Instructions for in-car use
13
• Fit the car safety seat with the child on the car seat,
remembering to secure the child with the safety harness.
•
The correct position of the safety seat in the car is parallel
with the ground, and so if necessary used rolled towels
under the safety seat to adjust the position.
14
•
Insert the webbing of the car seat belt into the two lateral
guides on the safety seat, ensuring that it is taut, and engage
the buckle of the car seat belt as shown in the figure.
15
•
Take hold of the car seat belt again and pass it behind the
backrest of the safety seat, inserting it into the rear guide
as shown in the figure.
16
•
In the car the handle must be fully lowered forward towards
the car seat backrest as shown in the figure. The correct
forward position is reached when it clicks into position. Check
that the seat belt is taut and locked to ensure adequate safety.
Cover removal
17
• To remove the safety seat harness:
•
press the metal button in the centre of the seat to extend
the safety harness braces;
•
press the red button on the crotch strap buckle to release
the harness;
•
release the harness braces from the metal buckle on
the back of the safety seat and unthread them from the
headrest and shoulder covers;
•
remove the two plastic covers on the back of the safety seat
by levering with a standard tip screwdriver, and unthread
the two side buckles and the central crotch strap buckle.
18
• To remove and uncover the headrest:
•
remove the cover pulling it downwards and slide it
carefully off the two side tabs;
• unscrew the two headrest screws with a screwdriver, press
the teeth on the slots and pull the headrest to release it.
19
• To remove the padding:
•
slide off the four padding fixing tabs from the edge of the
safety seat;
•
remove the two side guide covers for the car seat belt;
•
remove the metal button cover in the centre of the safety
seat, releasing it from under the seat;
•
remove the padding.
Padding cleaning instructions
• Brush the fabric parts to remove dust and hand wash at a
maximum temperature of 30° without wringing.
• Do not use chlorine bleach.
• Do not iron.
• Do not dry clean.
• Do not remove stains with solvents and do not tumble dry.
Refitting
20
• To refit the padding:
•
slide on the padding;
•
insert the four padding fixing wings on the edge of the
safety seat;
•
reposition the metal button cover in the centre of the
safety chair and engage it from under the chair;
•
position the two side guide covers for the car seat belt
with the slots facing the inside of the safety seat and check
that they are correctly engaged in position.
21
• To refit the headrest and cover:
•
from the back of the safety seat insert the headrest height
Summary of Contents for Primo Viaggio tri-fix
