CAUTION:
ADULT ASSEMBLY REQUIRED.
USE CARE WHEN UNPACKING AS COMPONENTS TO BE ASSEMBLED MAY POSE A SMALL PARTS/SHARP
EDGE HAZARD.
BATTERY IS INCLUDED AND MUST BE INSTALLED; see instructions 39-42
1 • Snap together the 2 halves of the bronze simulated engine.
2 • Insert the simulated engine into the vehicle, as shown in the figure.
3 • Press on the points shown by the arrows on the toy engine (on each side), to fasten the engine.
4 • Lift both rear shock absorbers, and line them up with the openings in the chassis.
5 • To fasten the shock absorbers to the chassis, insert the pins into the top holes on the shocks, with the tabs turned vertically (see detail).
6 • Finish fastening the shock absorbers by placing the plastic tool on the pins and hammering the pins all the way in.
7 • Snap the nut cap into place, and repeat the operation on the other three wheels.
8 • Attach seat by inserting black tabs on seat into slots on body. Then rotate down into place.
9 • Attach red seat lock by inserting through seat and into body.
10 • Attach black radiator piece by first inserting tabs into corresponding rectangular slots (a). Then press firmly on the upper tabs (b) so that they fully engage into
their slots.
11 • Position front rack onto supports as shown in figure and secure with 4 screws provided.
12 • Apply radiator decal.
13 • Insert the two brackets into the openings on the radiator, as shown in the figure.
14 • Attach charcoal front grill to front rack by lining up connection points and snapping into place.
15 • Attach the silver front brush guard by lining up connection points and snapping into place.
16 • Fasten the grill with the 2 screws.
17 • Attach the two chrome decals to the headlight positions on the grill.
18 • Snap the two headlights onto the grill.
19 • Attach the chrome decal to the chassis, as shown in the figure.
20 • Snap the taillight into place by inserting it from the top.
21 • To attach folding extra seatback, insert one of the posts into the rear rack.
22 • Position seatback with handle down and slide peg into hole on post.
23 • Slide second post onto peg on seatback (a) and then press post down into position (b).
24 • Folding extra seatback with posts in place.
25 • While holding seatback and posts in position, fasten posts using screws provided.
26 • Connect rear rail to rear rack by inserting tabs on rail into slots on rack, rotating into place and fastening using screws provided.
27• Position rear rack onto supports as shown in figure and secure with 4 screws provided.
28 • Snap the toy gas cap into place on the vehicle.
29 • Assemble handlebar/headlight unit as shown in figure.
30 • Apply chrome decal as shown in figure.
31 • Attach clear headlight lens.
32 • Attach black speedometer piece to headlight housing. Then apply speedometer decal.
33 • Attach clear speedometer lens and fasten using small screw provided.
34 • Slip the two handguards onto the handlebars, lining up the holes in the handguards with the holes in the handlebars.
35 • Fasten the hand guards with the two screws.
36 • Slip the handgrips onto the handlebars as shown.
37 • Snap handlebar into place on the vehicle.
BATTERY INSTALLATION
WARNING:
WARNING: BATTERY CHARGING AND ANY OTHER OPERATION ON THE ELECTRICAL SYSTEM MUST BE
CARRIED OUT BY ADULTS ONLY. THE BATTERY CAN ALSO BE CHARGED WITHOUT REMOVING IT FROM
THE VEHICLE.
38 • Turn the seat lock to the “unlock” position shown in the diagram, and lift the seat. NOTE: Seat has a lock and unlock position.
39 • Remove the battery retainer by squeezing in on the sides and sliding it free of the slot in the body.
40 • Slide the battery into the battery compartment.
41 • Connect wiring system of the vehicle (plug
A
) to the battery (plug
B
).
42 • Replace the battery retainer.
43 • Close the seat. ATTENTION: Always make sure that the seat is closed and locked after carrying out any operations inside it.
VEHICLE FEATURES AND INSTRUCTIONS FOR USE
44 • Exclusive
SmartPedal Technology™
feature allows for longer run times and more realistic driving. In “LOW” setting, when accelerator is pressed completely
down, forward motion at 3.5 mph is activated. In “HIGH” setting, when pedal is pressed completely down, forward motion begins at 3.5 mph for a few seconds
and then automatically accelerates to 7 mph. In “HIGH” setting, when pedal is released halfway, vehicle automatically “downshifts” to 3.5 mph. Brake activates
automatically when the child takes his foot off the accelerator.
45 • ATTENTION: For safety, when the vehicle is first removed from the packing, it is in the LOW setting. Peg Perego suggests that the LOW setting be used until
your child has become familiar with operating the vehicle. To adjust high-speed lockout, loosen screw.
46 • Then slide safety collar down into HIGH setting and replace screw.
47 • GEAR SHIFT LEVER: The vehicle has two directions. To use REVERSE (
R
), pull back and hold the gearshift lever. NOTE: For safety, gearshift must be held back
in the reverse position.
ASSEMBLY INSTRUCTIONS
INITIAL BATTERY CHARGE
!
• Remove battery and charger from packaging. Connect battery charger to a 120vac wall recepticle. Connect battery charger to battery.