Peavey Versarray 212, Specifications

Page: 12 / 20

12
Digitool MX
®
or VSX
™
48:
Four Versarray 212 cabinets @ 2 degrees angle between them
PEQ Freq = 325 Hz BW = 0.71 Level = - 2.5 dB
PEQ Freq = 2.5 kHz BW = 1.0 Level = - 3.5 dB
Also, reduce the PEQ on the 2.5” Midranges at 845 Hz from +4.5 dB
down to +3.5 dB.
OR
VSX 26 Front End gEQ (1/3 octave band type):
1/3 octave band 315 Hz set to – 2.0 dB; 1/3 octave band 400 Hz
set to – 0.5 dB; 1/3 octave band 1.6 kHz set to – 0.5 dB; 1/3 octave
band 2.0 kHz set to – 1.0 dB; 1/3 octave band 2.5 kHz set to – 2.5
dB; 1/3 octave band 3.15 kHz set to – 1.0 dB; 1/3 octave band 4.0
kHz set to –0.5 dB
Digitool MX – Front End Infrasonic filtering:
Filter/Gate = High Pass 12 dB per Octave at 34 Hz, Q = 0.71
EQ Section = High Pass 12 dB per Octave at 34 Hz Q = 0.71
OR
Use Crossover Function filter at 34 Hz, 24 db/Oct lR
( NOTE: The use of the front end filters on the Digitool will
provide infrasonic filtering for ALL of the drivers in the system,
while the use of the crossover function filter will only provide
that roll-off for the subwoofer)
limiters
VSX 26 (Preliminary settings. DO NOT DEPEND ON THE
lIMITER to prevent damage!)
Power Amp Gain set to 40X (32 dB)
Versarray 218:
Threshold: +7.0 dB
Ratio: 20:1
Attack: 100 ms
Release: 1000 ms
Versarray 212 Woofer:
Threshold: +4.0 dB
Ratio: 20:1
Attack: 60 ms
Release: 600 ms
Versarray 212 2.5” Midranges:
Threshold: -1.0 dB
Ratio: 20:1
Attack: 25 ms
Release: 250 ms
Versarray 212 Planar Ribbons:
Threshold: 0.0 dB
Ratio: 20:1
Attack: 10 ms
Release: 100 ms
Input limiter:
Threshold: +22 dB
Ratio: 20:1
Attack: 50 ms
Release: 500 ms
OR
For a more gradual soft limiting on the front end:
Input limiter:
Threshold: +10.0 dB
Ratio: 4:1
Attack: 25 mS
Release: 250 mS
Note: The VSX26 references the limiter settings to 0 dBu, which
is at –24 dBFS.
Digitool MX (Preliminary settings. DO NOT DEPEND ON THE
lIMITER to prevent damage!)
Input Gain Block= 18 dB
Output Gain Block= 24 dB
Power Amp Gain set to 40X (32 dB)
Versarray 218:
Threshold: -17.0 dB
Ratio: 20:1
Attack: 100 mS
Release: 1000 mS
Versarray 212 Woofer:
Threshold: -19.0 dB
Ratio: 20:1
Attack: 60 mS
Release: 600 mS
Versarray 212 2.5” Midranges:
Threshold: -25.0 dB
Ratio: 20:1
Attack: 25 mS
Release: 250 ms
Versarray 212 Planar Ribbons:
Threshold: -24.0 dB
Ratio: 20:1
Attack: 10 ms
Release: 100 ms
Input limiter:
Threshold: -2 dB
Ratio: 20:1
Attack: 50 ms
Release: 500 ms
OR
For a more gradual soft limiting on the front end:
Input limiter:
Threshold: -12.0 dB
Ratio: 4:1
Attack: 40 ms
Release: 500 ms
Note: The Digitool references the limiter settings to 0 dBFS, or
the maximum digital output levels of the system.
RE Subwoofers:
Versarray 218 Subs are shipped in 4-ohm mode (woofers
paralleled). There is an internal jumper change to allow
SPECIFICATIONS Versarray
™
212