SPECIFICATIONS
Versarray
™
112 Mk2
lower than the chart indicates.
Bandwidth (bw) to Q Chart
ß BW
Q .
0.25
5.764
0.500
2.871
0.577
2.484
0.707
2.020
1.00
1.414
1.305
1.069
1.50
0.920
2.00
0.667
2.50
0.511
Check with Peavey Electronics Corp., or visit the Peavey web
site at:
http://www.peavey.com
for the latest crossover and EQ setting information
INFORMATION ON THE FLYING HARDWARE FOR THE
Versarray
™
112 Mk2Mk2 (Available Separately)
Peavey
®
Versarray Model 25 Halo / Array Fly Bar
(formerly called the Versarray 112 Halo / Array Fly Bar)
Description
The Versarray Model 25 Halo / Array Fly Bar is designed to
be used in conjunction with the Versarray Model 25 Pull-Back
Bar, to safely rig and fly various models of Peavey speakers,
including the Versarray 100 series.
It includes four 1/2" X 13 thread eyebolts with 1 1/8" I.D.
eyes for rigging on the top of the bar, and a Versarray coupling
bracket interface, with holes for three captive 1/4" Quick
Release Push Pins, on either side of the bottom of the bar.
Coupling brackets are normally supplied with the Versarray
speaker modules, and are not included with the Versarray
™
Model 25 Halo/Array Fly Bar.
Specifications:
Dimensions: (H x W x D)
10.63" X 27.50" X 38.12"
Weight: 30.0 kg / 66 lbs.
Material: All steel construction, 2" by 3" welded steel frame
tubes with 3/16" wall thickness, center tongue 1/2 " thick
by 3" solid steel with _" rigging holes along it’s length,
coupling bracket mounts are dual 1/8" thick steel plates,
one set on each side. MIL spec eyebolts.
Finish: Entire Halo is flat black powder coated paint finish.
Working Load Limit: 409.1 kg / 900 lbs.
Ultimate Strength Design Factor: 7:1
Maximum Number of Versarray 112 Mk2 Cabinets Hung or
Flown: 16
Maximum Pull-Back Angle: 45 degrees
Maximum Number of Versarray 112 Mk2 Cabinets for Ground
Stack : 6
(When used with the Versarray Model 12 GSS bar)
Current Peavey FG#00588790 (as of 6/21/10)
NOTES:
The ultimate strength for the Versarray 112 Mk2
loudspeaker system module rigging points was determined
utilizing calibrated and certified destructive pull tests.
Before you fly the array, be sure to inspect the rigging and flying
hardware to insure that it is mechanically sound and has not
been damaged, there should be no significant distortion of the
shape of the coupling brackets, cabinet brackets, or fly bar, and
the hardware should be checked for tightness.
IF ANY OF THE BRACKETS, OR THE FLY BAR HAS BEEN DAMAGED
OR DISTORTED, DO NOT USE, AND DO NOT FLY THE ARRAY UNTIL
THEY CAN BE REPLACED OR REPAIRED!
DO NOT USE THE COUPLING BRACKETS AS HANDLES TO
TRANSPORT THE CABINETS!
Use only the correct mating hardware. All associated rigging is
the responsibility of others.
NOTICE:
The Quick Release Positive Lock Pins from the Versarray
200 series WILL NOT fit into the rigging system holes on the
Versarray 100 series. The Versarray 200 series uses 3/8" diameter
pins, and the Versarray 100 series uses 1/4" diameter pins.
Peavey
®
Versarray Model 25 Pull-Back Bar/ Small Array Fly Bar
(formerly called the Versarray 112 Fly Bar)
Description
The Versarray Model 25 Pull-Back Bar is designed to be used in
conjunction with the Versarray Model 25 Halo/Array Fly Bar, to
safely rig and fly various models of Peavey speakers, including
the Versarray 100 series.
It can also be used by it self as a small array fly bar, to fly no
more than a maximum of seven Versarray 112 Mk2 cabinets. In
this mode, it can be coupled directly to the VersaLift
™
lift to fly
up to six Versarray 112 Mk2 cabinets up to 13 feet above ground,
centered over a Versarray 218 Sub. Shackles are included for
coupling to the VersaLift, or other rigging.
We recommend that for any line arrays of more than six Versarray
112 Mk2 cabinets, that the Versarray Model 25 Halo/Array Fly Bar
be used in conjunction with the Versarray Model 25 Pull-Back
Bar/Small Array Fly Bar as a pull-back bar.
It incorporates two 3/8" X 16 thread eyebolts with 1" ID eyes for
rigging on the top (or rear) of the bar, and a Versarray coupling
bracket interface on each side of the bar, with holes for captive
1/4" Quick Release Push Pins (included), on either side of the bar.
Specifications:
Dimensions: (H x W x D)
4.13" X 27.50" X 1.75"
Weight: 1.8 kg / 4 lbs.
Material: All Steel construction, 1" square steel tubing with
1/8" wall thickness, end fittings made from 1/8" steel plate.
MIL spec eyebolts & shackles.
Finish: Flat black powder coated paint finish.
Working Load Limit: 196.4 kg/432 lbs
Ultimate Strength Design Factor: 9.6:1
Maximum Number of Versarray
™
112 Mk2Cabinets Hung or
Flown: 7
Maximum Pull-Back Angle: 45 degrees
Current Peavey FG# 00584970 Black,
Summary of Contents for Versarray 112 Mk2
