to the cabinet to strain relief the IEC power cord connected to the amplifier module at (2) so the power cord cannot
be pulled out or vibrate loose.
Use oF tHe pVXp
™
15 WitH A sUBWooFer poLe tUnneL
The built-in stand-mount cup allows use with the Peavey
®
SP
®
118 Sub and the accessory pole that it is
designed to use, Peavey part #00326530. The pole used is 51-3/4" long and has a nominal diameter of 1-3/8".
Always be sure to place the subwoofer used in this manner on a flat, level and stable surface.
Use oF tHe pVXp
15 WitH A speAKer stAnD
The PVXp 15 has a stand-mount cup molded-in so that the system can be stand mounted on a standard 1-3/8”
(36mm) diameter stand pole. When using stands or poles, be sure to follow these precautions:
Check the stand or pole specs to make sure that it can support the weight of the PVXp 15 (51 lbs./23.2 kg),
and observe all safety precautions stated by the stand manufacturer, including the maximum height the
stand is rated for.
Always place the stand on a flat, level and stable surface, and be sure to fully extend the stand legs as
per the stand manufacturer’s instructions.
Try to make sure that the stand legs are oriented for the least danger of tripping to those in the vicinity of
the stand. Never block a doorway or hallway with the legs of a stand.
Try to route cables so that people will not trip over them, or tip the speaker over. Use of duct tape, cable
channels or guards, or other appropriate tie-down/cover–up devices should be carefully considered and
implemented.
When installing or de-installing the speaker on the stand, it is a good practice to have a helper if
possible, as it can be hard to “thread the needle” and mate the stand cup to the stand pole while holding
the PVXp 15 speaker system at arm’s length. It is also helpful if someone holds the speaker stand and
pole down while the PVXp 15 is removed from the stand pole. This prevents the PVXp 15 from pulling the
pole up with it.
When using stands outdoors, never attach banners or flags to the stands or the PVXp 15 speaker system,
strong winds may cause the speaker to blow over. If there is a possibility of windy conditions, then it
may be prudent to consider weighting or locking down the stand legs to prevent the PVXp™15 speaker
system from being blown over.
connectinG A siGnAL to tHe pVXp
15
T
here are a variety of ways to input a signal to the PVXp 15.
The input (4) provides either a balanced mic- or line-level input, allowing the use of a 1/4" TRS (tip-ring-sleeve)
type phone plug or a male XLR plug.
Do not connect cables to the jacks while the unit is ON and the Level knob is turned up! While a standard
single-ended 1/4" phone plug-equipped cable will work well and the balanced input circuitry will provide some
interference rejection, a balanced cable using either the balanced TRS 1/4" phone plug or the XLR plug will
provide superior interference rejection and performance.
Sometimes, with difficult interference problems, it will be helpful to lift the shield ground ( Pin #1 of an XLR) of
a balanced cable at the PVXp 15 end. Check any input changes carefully, always turning the Level control down
before plugging and unplugging cables, or lifting the ground.
Use of high-quality, premium cables is recommended for the PVXp 15, as these usually have better shielding and
materials and will provide greater long-term reliability. The best option is a shielded, balanced cable no longer
than necessary to reach the PVXp 15. It is usually a good idea to leave some slack at the input to the PVXp 15
and also to tape the cables down or run them under a cable guard to avoid anyone tripping over them or pulling
the PVXp 15 over when stand mounted.
LeVeL controL ADjUstMent
The PVXp 15 is equipped with a Level control (6) on the input to facilitate use in many different applications.
With the Level control adjusted fully clockwise, gain is at maximum and the input sensitivity is 0.54 V RMS for
