Loudspeaker System Specifications
9
GROUPING OF INSERT SETS
Group A
A set of two widely spaced M8 inserts on the top, designed to hang the cabinet
using the proper eyebolts.
Group B
A set of two widely spaced M8 inserts on the bottom, designed to hang the
cabinet using the proper eyebolts.
Group C
A set of four M8 inserts on the top, designed to be used with the Peavey
Versamount
™
70 mounting bracket.
Group D
A set of four M8 inserts on the bottom, designed to be used with the Peavey
Versamount
™
70 mounting bracket.
For Group A and B, always use both inserts as a pair; NEVER use just one insert
to fly a cabinet!
For Group C, and D, Always use all four inserts of a given group as a set;
NEVER use just one insert to fly a cabinet! The four insert groupings are meant
to have all four inserts used at once within a group.
Group D should only be used with the Versamount
™
70 oriented beneath the
cabinet, and at an angle less than 30 degrees from vertical.
SPECIFICATIONS FOR INSERT MATING HARDWARE
Group A and Group B should use an M8 forged steel shoulder-type lifting
eyebolt, which meets the requirements of DIN 580 or ASTM A489. They should
only be used in pairs, and in conjunction with the rear most pair of M8 inserts on
the same surface as a pull-back/aiming adjustment, using M8 eyebolts of a
similar specification. The length of the threaded shank on the eyebolts should
not exceed 0.709
” (approx.
18 mm), so that it does not bottom out in the insert.
Thread pitch: 1.25 mm per thread.
The length of the threaded shank into the cabinet on the rear M8 eyebolt should not
exceed 0.709” (approx. 18 mm), so that it does not
bottom out in the insert. Thread
pitch: 1.25 mm per thread.
Group C should use an M8, grade 8.8 or better, 1.25 mm per thread, metric bolt,
that does not penetrate the cabinet past the cabinet surface more than 0.709
”
(approx. 18 mm). When using a Peavey Versamount
™
70 mounting bracket
Loudspeaker System Specifications
10
and lock washer, the length of the bolt should not exceed 1.00
” (approx.
25
mm).
Group D should use an M8, grade 8.8 or better, 1.25 mm per thread, metric bolt,
that does not penetrate the cabinet past the cabinet surface more than 0.4
00”
(10 mm). When using a Peavey Versamount
™
70 mounting bracket and lock
washer, the length of the bolt should not exceed 3 / 4” (approx. 20 mm).
WARNING! (note to structural engineer)
The thread insertion depth past the surface of the cabinet of the end of the
mounting bolt should not be more than 0.787” (20 mm) for insert groups A, B,
and C, and not more than 0.400
” (1
0 mm) for Group D.
If these thread insertion depths are exceeded, then the inserts may be damaged
or unseated from the cabinet, severely compromising the mounting integrity of
the cabinet!
For maximum mounting strength, safety and reliability, the bolt threads should
engage at least 8 mm of depth for Group A, B, C, and D.
The
PVX™p 10 Bluetooth®
mounting insert groups C, and D are designed to be
used with
the Peavey® Versamount™ 70
mounting bracket (00454470 black,
00454460 white. It can also be used with the Peavey® Wall-Mount Speaker
Stand (00922940 black, 00487390 white), which will fit into the built-in stand
mount cup on the bottom of the cabinet.
Connecting AC Power To The
PVX™p 10 Bluetooth®
The
PVX™p 10 Bluetooth®
comes with an 6-foot IEC connection AC power
cord. If you are using an extension cord or power strip with this powered
speaker, make sure it is of good quality and of a sufficient current capacity to
maintain safety and maximize the power output capability of the
PVX™p 10
Bluetooth®. For maximum undistorted output, do not connect any other device
to the same extension cord that the
PVX™p 10 Bluetooth®
is connected to. Do
not exceed the rated current capacity of the extension cord with the sum total of
all units connected to it.
When first plugging in the AC cord, make sure the power switch is in the Off
position, and then turn it On only once the power cord has been connected.
Built-in muting will engage when the proper sequence of steps is taken.
Special Note for Permanent Installation
When installing the
PVX™p 10 Bluetooth®,
AC power runs will be used and a
certified electrician should be consulted to be sure that all AC wiring complies
with local codes and regulations. It is also advisable to use a cable clip properly
