10
Power amplifier section:
Rated power and load:
80 Watts RMS into 4 Ohms (with DDT
™
compression)
Frequency response:
+0, -3 dB, 20 Hz to 20 kHz @ 80 Watts
RMS into 4 Ohms
Total harmonic distortion:
Less than 0.3%, 1 Watt to 80 Watts RMS,
20 Hz to 20 kHz, 4 Ohms
DDT
™
dynamic range:
Greater than 20 dB
DDT maximum THD:
Below 0.8% THD for 6 dB overload
Below 3.5% THD for 20 dB overload
Hum and noise:
Greater than 83 dB below rated power
Power consumption:
200 Watts, 50/60 Hz, 120 VAC (domestic)
Preamp section:
The following specs are measured @ 1kHz
with the controls preset as follows:
Master gain @ 10
Low EQ @ 0 dB
Mid EQ @ 0 dB
Mid Shift @ 600 Hz
High EQ @ 0 dB
Presence EQ @ 0 dB
Reverb @ 0
Nominal levels are with pre gain @ 5
Minimum levels are with pre gain @ 10
Preamp high gain input (no pad):
Impedance: High Z, 220 k Ohms
Nominal input level: -29.9 dBV, 32 mV RMS
Minimum input level: -53.2 dBV, 2.2 mV RMS
Maximum input level: 8 dBV, 2.5 V RMS
Preamp Low Gain Input (-10 dB pad):
Impedance: High Z, 68k Ohms
Nominal input level: -19.9 dBV, 101 mV RMS
Minimum input level: -43.2 dBV, 6.9 mV RMS
Maximum input level: 18 dBV, 8 V RMS
Pre EQ patch send:
Load impedance: 10k Ohms or greater
Nominal output level: -18.6 dBV, 117 mV RMS
Pre EQ patch return:
Impedance: High Z, 220 k Ohms
Designed Input Level: -18.6 dBV, 117 mV RMS
(Switching jack provides send to return
connection when not used)
Post EQ patch send:
Load impedance: 10 k Ohms or greater
Nominal output level: -14.1 dBV, 198 mV RMS
Post EQ patch return:
Impedance: High Z, 1 m Ohms
Designed Input Level: -14.1 dBV, 198 mV RMS
(Switching jack provides send to return
connection when not used)
XLR line output:
Load impedance: 5 k Ohms or greater
Nominal output level: -3.1 dBV, 0.7 V RMS
Preamp output / CD input:
Load impedance: 10 k Ohms or greater
Nominal output level: -3.1 dBV, 0.7 V RMS
Nominal CD Input Level: -3.1 dBV, 0.7 V RMS
(Stereo cable must be used for CD Input
to function)
Power amp input:
Impedance: High Z, 27 k Ohms
Designed Input Level: -3.1 dBV, 0.7 V RMS
(Switching jack provides preamp output
to power amp input connection when not
used)
System hum and noise @ nominal input
level:
(20 Hz to 20 kHz unweighted)
Greater than 75 dB below rated power
Equalization:
Low: +/-15 dB @ 45 Hz, shelving
Mid: +/-15 dB @ Mid Shift frequency,
boost/cut
Mid Shift: 150 Hz to 1.5 kHz
High: +/-15 dB @ 6 kHz (special EQ)
Presence: +/-15 dB @ 10 kHz, shelving
Select effects: Post EQ effects Loop defeat
Reverb: Reverb defeat
Dimensions (H x W x D):
18.125" x 21.375" x 10.250"
Weight:
42.3 lbs.
Nashville
™
112
SPECIFICATIONS
External footswitch (part #03022910,
not included) functions:
Logo referenced in Directive 2002/96/EC Annex IV
(OJ(L)37/38,13.02.03 and defined in EN 50419: 2005
The bar is the symbol for marking of new waste and
is applied only to equipment manufactured after
13 August 2005
www.peavey.com
Warranty registration and information for U.S. customers available online at
www.peavey.com/warranty
or use the QR tag below
Features and specifications subject to change without notice.
Peavey Electronics Corporation 5022 Hartley Peavey Drive Meridian, MS 39305 (601) 483-5365 FAX (601) 486-1278
