Peavey Dm 112 Operating Manual Download Page 3

Introduction

Thank you for purchasing the powered Peavey® DM™ 112 powered speaker system.  The DM™112 features a 

reliable bi-amped power section that provides a total of 660 Watts of peak available dynamic power with signal 

compression to prevent audible overload.  The analog power amplifiers and linear power supply are coupled 

with a DSP based crossover and EQ.

The LCD display and EQ presets along with other operating parameters are accessed via a one-knob selector.  

The DM™112  provides a balanced input via a combination jack that accepts balanced TRS 1/4 inch input as well 

as a balanced XLR input.   There is a balanced Thru output via a Male XLR.  There is an adjustable Gain control 

as well as a combination LED indicator that lights when power is on and changes color when the “soft-limiting” 

compression circuit is activated.

Features

*  Two-way bi-amplified analog amp powered speaker system

*  12” heavy-duty woofer

*  DX™14 compression driver, with 1.4 inch titanium diaphragm

*  410 watts peak woofer power, 250 watts peak tweeter power

*  DSP processing is 64 bit double-precision

*  DSP I/O is at 96 kHz and 24 bits, with low-jitter, professional grade components

*  Dynamic bass boost function

*  Fan cooled for maximum reliability

*  Patented Quadratic Throat Waveguide™ technology, 110 by 80 degree coverage

*  Input is via a combo female XLR and 1/4” TRS phone jack with balanced input

*  A Mic/Line switch provides for two different gain settings

*  Thru output is via a male XLR jack

*  Multiple Factory Preset EQ settings for the DSP crossover system

*  User Preset EQ storage provisions allow storing custom presets for later recall

*  Rugged plastic injection-molded trapezoidal enclosure

*  Cabinet has dual rear corner angled sides for floor monitor use.

*  Full-coverage perforated steel grille, with powder coat finish

*  Pole mount molded-in for 1 3/8” diameter poles

Description

The DM™112 is a two-way sound reinforcement system based on a heavy-duty 12” woofer and a DX™14 titani-

um diaphragm dynamic compression driver mounted on a 110 by 80 degree coverage Quadratic Throat Wave-

guide™.   It’s contemporary appearance coupled with exceptional performance offer an highly desirable combi-

nation.

The light yet durable injection-molded plastic enclosure with molded-in stand mount cup eases portable use for 

live music or PA sound.  The trapezoidal cabinet has three handles for ease of portability, and two extra angled 

sections on either side to allow use as a floor monitor.  A full length black powder coated perforated steel grille 

provides system protection and a professional appearance.

The heavy-duty 12” woofer has a warm punchy sound for plenty of bass.  The DX™14 compression driver tweet-

er is coupled to a Quadratic Throat™ constant directivity waveguide, covered under US patent #6,059,069 with 

ENGLISH

Summary of Contents for Dm 112





















Reviews: