background image

13

POWER AMPLIFICATION 
SECTION

RATED POWER AND LOAD:

120 W RMS into 16, 8, or 4 ohms

POWER @ CLIPPING:

(Typically @ 5% THD, 1 kHz, 120 V AC 
line)
130 W RMS into 16, 8, or 4 ohms
(Bias must be reduced to measure.)

FREQUENCY RESPONSE:

+0, -3 dB, 50 Hz to 20 kHz @ 100 W 
RMS into 8 ohms

HUM AND NOISE:

Greater than 75 dB below rated power

POWER AMP EQ:

Active Presence:

 +10 dB @ 2 kHz

Active

 

Resonance:

 +10 dB @ cabinet 

    resonant frequency

POWER CONSUMPTION (Domestic):

400 watts 50/60 Hz, 120 V AC 
(Domestic)

TUBE COMPLEMENT:

6-12AX7 preamp tubes
(1 for clean/crunch, 3 for Lead, 1 for 
EFX and 1 phase splitter
4-6L6GC

PREAMP SECTION

The following specs are measured @ 
1 kHz with the controls preset as follows:
 

Low and High EQ @ 10

 

Mid EQ @ 0

 

Bright out

 

Lead and Rhythm Posts @ 10

 

Presence and Resonance @ 0 dB

 

Nominal levels with Pre Gains @ 5

 

Minimum levels with Pre Gains @ 10

PREAMP INPUT:

Impedance:

 Very high Z, 470K ohms

Lead Channel

 (with channel select in):

Nominal Input Level:

 -60 dBV, 

1 mV RMS

Minimum Input Level:

 -76 dBV, 

.15 mV RMS 

Clean

 

Channel

 (with channel select out):

Nominal Input Level:

 -30 dBV, 

    30 mV RMS

Minimum Input Level:

 -34 dBV, 

   20 mV RMS

Maximum Input Level:

 0 dBV, 

    1.0 V RMS
(Subtract 24 dB with Crunch switch in.)

EFFECTS SEND:

Load Impedance:

 47 k ohms or greater

Nominal Output

: -10 dBV, 300 mV RMS

EFFECTS RETURN:

Impedance:

 Very High Z, 470 k ohms

Designed Level:

 -10 dBV, 300 mV RMS

PREAMP OUT:

Load Impedance:

 47 k ohms or greater

Nominal Output:

 +10 dBV, 3 V RMS

REMOTE FOOTSWITCH:

Special 3-button unit with LED indicators 
   (supplied)
Channel select and reverb

SYSTEM HUM AND NOISE @ 
NOMINAL LEVEL (clean channel):

(20 Hz to 20 kHz unweighted)
Greater than 63 dB below rated power

EQUALIZATION:

Custom Low, Mid, and High passive type EQ

Push Bright (Rhythm Channel only)

+6 dB @ 2 kHz

Push Crunch (Rhythm Channel only)

Increases gain

DIMENSIONS (H x W x D):

10" x 26.625" x 11.75"
(25.4 cm x 67.6 cm x 29.8 cm

WEIGHT:

48.3 lbs. (21.91 kg)

6505

+

SPECIFICATIONS

Features and specifications subject to change without notice.

Summary of Contents for 6505 Plus 112













Reviews: