Connecting the Drive Shaft Assembly
Connect the ends of the Drive Shaft (A) to the
short extensions (B) on the Main and Slave Side
Pedals and tighten Key Bolt 1 and then Key Bolt 2
(Fig.13 ,14).
Loosen the Key Bolts on the Center Connecting
Tube of the Drive Shaft Assembly and adjust the
distance between the Main Pedal and the Slave
Side Pedal to your liking. Re-tighten the Key Bolts
(Fig.15-A).
Fig.13
Fig.14
Drive Shaft
Drive Shaft
Key Bolt
Key Bolt
Velcro Strips
Velcro Strips for Slip Prevention
Velcro Strips are provided with P-3002C Double
Pedals to help prevent slipping when used on
carpeted floors. To apply, peel off the backing on
the Velcro Strips and apply them in the locations
shown. Clean the surfaces thoroughly with alcohol
and dry completely for best adhesion (Fig.18).
Fig.18
Setting Examples
The Aluminum Traction Dots can be replaced with
optional NP-283N/7 Rubber Dots for more traction.
Allen Screw
Allen wrench
Adjustment Knob
Wing Bolt
Hoop Clamp System
The P-3002C Hoop Clamp System is designed
with Spherical Rubber Grips allowing the front of
the bass drum to be raised while keeping the
pedal flush on the floor. Insert the bass drum hoop
into the Clamp, and turn the Wing Bolt to secure.
The Clamp comes preset from the factory to
accommodate most bass drum hoops but if
necessary it can be adjusted to fit thicker or
thinner hoops. Loosen the Allen Screw on the
Adjustment Knob with the provided Allen wrench
(2.5mm) as shown and tighten or loosen the
Adjustment Knob until proper fit is achieved then
re-tighten the Allen Screw (Fig.17). If the heel
plate of the pedal lifts while playing, try loosening
the Adjustment Knob to change the angle of the
Hoop Clamp until the pedal remains flat.
Fig.17
Upper Nut
Spring
Lower Nut
Click Lock
Spring Tension Adjustment
The P-3002C Demon Chain Double Pedal features
our patented Click Lock spring tension retention
system. To increase the spring tension, disable
the Click Lock by lifting the lever upward, loosen
the Upper Nut and tighten the Lower Nut until the
desired tension is achieved (Fig.16-A). To
decrease spring tension, disable the Click Lock
by lifting the lever upward, loosen the Upper Nut
and loosen the Lower Nut until the desired tension
is achieved. When the desired spring tension is
achieved, tighten the Upper Nut to keep the
spring tension from loosening then press the Click
Lock lever down to engage the grooves around
the Lower Nut until you feel the lever "Click"
(Fig.16-B). Before playing, make sure that both
Upper and Lower Nuts are tight and the Click
Lock lever is in a vertical position with both sides
of the lever engaged in the grooves around the
Lower Nut.
Fig. 16-B
Fig.16-A
Fig.15-A
Fig.15-B
B
A
A
B
Heel Plate
Hinge
3-Piece Screw
Flat Head Screw
Flat Head
Screw
3-Piece
Screw
Bottom Plate
Footboard
Place the Heel Plate between the Footboard and
the Hinge (Fig.12) and attach the Heel Plate with
the remaining two 3-Piece Screws using the
Mutli-Function Drum Key or Allen wrench (3mm).
Attach the Hinge to the Bottom Plate with two Flat
Head Screws using the Multi-Function Drum Key
or Allen wrench (3mm) (Fig.12). The Hinge is now
located at the back of the Footboard to achieve a
Long Footboard.
Fig.12
Tip
Traction Dot
3-Piece Screw
Traction Plate
Traction Plate / Traction Dots
The Traction Plate adjusts to a variety of grip/slide
configurations. To change the position of the
Traction Dots, use the Multi-Function Drum Key or
Allen wrench (3mm) to remove the 3-Piece Screw
beneath the footboard and remove the Traction
Plate (Fig.19). Rearrange the Traction Dots to your
preference and replace the Traction Plate.
Fig.19
https://www.pearldrum.com
Products and specifications are subject to change without notice.
Printed in China
-Jan 2021-
Tip
If the Drive Shafts are extended too far, they will
separate from the Center Connecting Tube. Reassem-
ble them with the dots aligned as shown in Fig.15-B.
Tip
Tip : You may need to rotate the Drive Shaft Assembly
to bring the footboard of the Slave Side (left) Pedal to
the proper playing height (angle) before attaching the
Drive Shaft Joints (A) to both pedals.
Tip
The Duo-Deck Footboard
uses two different types of
screws. Make sure to use
the correct screws.
