SAFETY INSTRUCTIONS FOR PUMP
CAUTIONS:
•
The pump has been evaluated for use with water only.
•
Risk of electric shock.
•
Do not remove cord and strain relief. Do not connect conduit to pump.
•
Do not use the pump in water exceeding 86ºF / 30ºC.
•
Do not use the pump in flammable liquids.
•
Do not use the pump for industrial purposes.
•
Do not use the pump in vehicles or on board ships or aircraft or swimming pools.
•
Do not use the pump in location where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapor or
gas).
•
Do not let the pump run dry. Pump must be completely submerged for proper operation and cooling.
•
Do not lift the pump by its power cord.
•
Keep the plug dry. Do not expose the plug to water or steam.
•
Before connecting to the power source, make sure that the pump is assembled and completely submerged in water.
•
Always disconnect the pump from the power source before performing any maintenance on the pump, lights (if equipped), or fountain.
•
Do not exceed the voltage shown on the pump.
•
Check the water level regularly to ensure the pump is completely submerged during operation. The pump should be fully submerged during
operation. Do not add water while operating the product. Always disconnect the pump from the power source before adding water.
WARNINGS:
1.
Risk of electric shock. This pump is supplied with a grounding conductor and grounding-type attachment plug. To reduce the risk of electric
shock, be certain that it is connected only to a properly grounded, grounding-type receptacle.
2.
To reduce the risk of electric shock, use only on portable self-contained fountains no larger than 5 ft / 1.52 m in any dimension.
3.
If equipped with a 3-prong, grounded type plug, do not remove the grounding pin from the plug on the power cord.
CARE AND MAINTENANCE
1. Distilled water is always recommended to fill your fountain. Distilled water is pure and should have no minerals or sediment in it. It will extend the
life of the pump and the time between cleanings. If distilled water is not an option, use filtered water, as water directly from your tap will generally
have minerals and chemicals that can build up and leave behind residue on your fountain.
2. Check the water level regularly to ensure the pump is completely submerged during operation. This is necessary ensure proper cooling of the
pump and prevent overheating. In summer months, or dry, hot climates, water evaporates very quickly, so it may be necessary to check the water
level every day. The rate of water evaporation will also be greater with larger fountains, with more surface area, than smaller fountains.
3. Keep the fountain water and pump clean and clear of debris. If placed under a tree or near vegetation, you may need to scoop out leaves and
other debris every other day. Water treatments that prevent algae growth and mineral deposits are available at your local home & garden stores.
Do not use bleach as it may be harmful to pets and wildlife and may also damage the finish of the fountain.
4. Clean the fountain monthly to prevent mineral deposits and contamination which may clog the pump.
Disconnect the pump from the power source and empty the water from the fountain. Use any gentle household cleanser and a soft brush or cloth
to clean the fountain. Avoid using any harsh chemicals, abrasives or rough scrubbing, as this could damage the finish on your fountain. The
frequency of cleaning may vary depending on the location of your fountain.
5. Use a pre-filter on your pump if available to prevent it from clogging with leaves or other debris.
6. Regular cleaning of the pump will be necessary depending upon the environment in which it is operated. Clean the pump when it is visibly soiled
or when a noticeable decrease in performance is detected. Failure to clean the pump will result in overheating of the pump. .
7. Before cleaning, always disconnect the pump from the power source.
8. Disassemble the pump by removing the filter and regulator/impeller plate. Remove the impeller/rotor assembly by gently pulling on the impeller
blades. Use a soft cloth or brush to clean the area inside of the pump housing. Clean the filter, gland and impeller in warm soapy water.
Reassemble the pump and
inspect for proper operation. Please see the diagram which matches your pump below:
5
