manualshive.com logo in svg

PeakTech 2670, Operation Manual

Share
Download
PeakTech 2670 Operation Manual Download Page 13

Buzzer sound below  under 10

Ω

 (on 20

Ω

 range) 

 
Withstand voltage 

meet  EN  61010  safety  requirements   
category III 

 
Dimensions (WxHxD)  170x165x92 with housing front cover 
 
Weight 

1,04 kg 

 
Standard  
accessories 

test  leads,  alligator  clips,  carrying  belt, 
batteries and manual 

 

8. Maintenance 

 

CAUTION: 

Always  disconnect  the  test  leads  from  the  instrument  before 
attempting battery or replacement. 
 

8.1. Batteries replacement 

When  the  LCD shows  the  low  battery  flag,  the  batteries  need 
replacing.  Eight  batteries  (AA  or  equivalent)  are  required. 
Alkaline  types  are  recommended.  Open  the  battery 
compartment  lid  on  the  back  of  the  instrument  by  unscrewing 
the screw. Replace all eight batteries with new ones observing 
the  correct  polarity.  Close  the  battery  compartment  lid  and 
replace the screw before using the tester. 
 

8.2. Fuse replacement 

Open  the  battery  compartment  lid.  Remove  the  fuse  conver 
and  the  old  fuse  and  replace  with  the  new  one.  Replace  the 
fuse  conver  and  screw  the  battery  compartment  lid  back  on 
before using the tester. 
 
 
 

-12- 

Summary of Contents for 2670
















Reviews:

No comments

Brands by name

Popular brands

Load more brands