manualshive.com logo in svg

Peak Atlas DCA75 Pro, User Manual

Share
Download
Peak Atlas DCA75 Pro User Manual Download Page 11

Peak Atlas DCA Pro

 User Guide

June 2019 

–

 Rev 1.7

Page 11

 LEDs

An LED (light emitting diode) is really just another type of diode,
however, the 

DCA Pro

will determine that an LED or LED network

has  been  detected  if  the  diode

’

s  measured  forward  voltage  drop  is

between 1.5V and 4.0V. This also enables the 

DCA Pro

 to intelligently

identify bicolour LEDs, both two-lead and three-lead varieties. See the section
on bicolour LEDs for more information.

For two leaded parts, connect any pair of the 3 test clips to your LED. Leave
the 3

rd

 test clip unconnected.

In  this  example, the  Red  test  clip  is
connected  to  the  LED

’

s  Cathode

(negative)  and  the  Blue  test  clip  is
connected to the Anode (positive).

The forward voltage of the LED is measured at a nominal current of 5mA. You
can test at different currrents by performing an I/V graph with the PC software.

During the analysis process, the LED will briefly illuminate (so you can
see its illumination colour). The test current of 5mA (and the short pulse
duration)  means  that  it  may  not  be  as  bright  as  you  expect,  LEDs  are
often used at currents of 10-20mA. Power LEDs are sometimes driven
at 350mA or more.

Infra-red LEDs (including LEDs used in opto-isolators can have typical
forward  voltages  of  less  than  1.5V  at  5mA.  This  means  that  the

DCA Pro

 will identify the device as a diode (instead of an LED). That is

normal  and  does  not  indicate  a  fault.  The  pinout,  forward  voltage  and
test current values displayed are correct.

ork

p is

gently

Summary of Contents for Atlas DCA75 Pro

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands