background image

Page 25

Start-Up Sequence

Switch the generator on using the power switch on the rear panel of the unit. Please 

note: On 30L generators, air will only flow through the generator when the power is 

switched on. The LED’s on the front panel will illuminate 

YELLOW

 for the start-up 

period.

On completion of the start-up period, up to 60 minutes, the fascia will illuminate 

GREEN 

or

 BLUE (70-**** Part Numbers Only)

. The generator is now ready to be used.

On Demand Gas

The generator system will produce zero air on demand. If the application is operating 

and requires a gas flow, the generator it is connected to will supply this to suit the 

requirements of the application. If the application requirement for gas stops, the 

system will also stop. If the demand from the application starts again, the system will 

automatically start again to suit the demand.

Unusual Operation

If at any time the generator begins to emit excessive noise or vibration, then it should 

be switched off and you should contact Peak Scientific or the Peak Partner from which 

the generator has been purchased.

YELLOW for 60 Minutes

GREEN / BLUE

Summary of Contents for Precision Zero Air 1.5L

































Reviews: