background image

Page 5

Warranties and Liabilities

1.  The Company warrants that it has title to the Goods.
2.  Subject to the provisions of this clause the Company warrants that the Goods  

 

shall comply in all material respects with any specification referred to in the Order  

Confirmation (as the same may be amended) and shall, subject thereto, be free    

from defects in material and workmanship for the lesser of a period of twelve  

 

months from the date of delivery or thirteen months from the date of dispatch    

from the factory.

3.  Save as provided in this clause and except where the Goods are sold to a person   

dealing as a consumer (within the meaning of the Unfair Contract Terms Act  

 

1977) all warranties, conditions or other terms implied by statute or common  

law are hereby expressly excluded save to the extent they may not be lawfully 

excluded. When the Goods are sold to a consumer within the meaning of the Unfair 

Contract Terms Act 1977 their statutory rights are not affected by the provisions of 

this clause.

4.  In the event of the Customer making a claim in respect of any defect in terms of   

clause 2 hereof the Customer must. 

1.  Reasonably satisfy the Company that the Goods have been properly installed, 

commissioned, stored, serviced and used and without prejudice to the generality 

of the foregoing that any defect is not the direct or indirect result of lack of repair 

and/or servicing, incorrect repair and/or servicing, use of wrong materials and/or 

incorrect spare parts 

2.  Allow the company to inspect the Goods and/or any installation and any relevant 

packaging as and when reasonably required by the Company.

5.  Subject to the Company being notified of any defect as is referred to in sub- 

 

clause 2 hereof within a reasonable time of it becoming apparent and subject always 

to the terms of sub-clause 4 hereof, the Company shall, in its option, replace or 

repair the defective Goods or refund a proportionate part of the Price. The Company 

shall have no further liability to the Customer (save as mentioned in sub-clause 6 

hereof).

6.  The Company shall be liable to indemnify the Customer in respect of any claim 

for death or personal injury to any person in so far as such is attributable to the 

negligence or breach of duty of the Company or any failure by the Company to 

comply with the provisions of sub-clause 2 hereof.

7.  Save as provided in sub-clause 2 hereof the Company shall not be liable in respect 

of any claim by the Customer for costs, damages, loss or expenses (whether direct, 

indirect, consequential or otherwise) or indemnity in any respect howsoever arising 

including, but not by way of limitation, liability arising in negligence (other than 

pursuant to clause 6 above) that may be suffered by the Customer or any third 

party.

Summary of Contents for Genius 1050





































Reviews: