background image

Step 1

Part Identification

Layout out all of the parts and pieces that came with the 
big sweep. Using the exploded parts view on the previous 
page, identify each of the parts and the quantities. We 
will be using the reference numbers in exploded parts 
view throughout the instruction process.

Step 2

Assemble the Track Mounting Blocks (22)

 

To do this, thread a Studded T-knob (24) into the upper 
hole on one of the blocks as shown. Do not thread all 
the way through. Next, thread a locking set screw (23) 
into the lower hole as shown. Do not thread all the way 
through. Once you are completed with the first block, 
repeat this process for the other two blocks. 

Step 3

Install T-Track Mounting Blocks

Slide the T-Track Mounting Blocks (22) on to the single 
slotted side of the Mounting Track (21) making sure that 
each block is facing the same direction as shown above.

Step 4

Attach the Track and Mounting Block Assembly 

Please note that all lathes are different as far as shape. 
The blocks are designed to slide along the track to adapt 
to the shape of your lathe. Start at one end of the track 
and secure the block to your lathe by tightening the 
Studded T-knob (24). Attach and secure the next block fol-
lowed by the third block. Lock the track in place by tight-
ening the Set Screws (23) with a philips head screw driver.  

Step 5

Assemble the Lower Support Bracket Assembly.

 

A

.

 

Insert the 5/16” (16) bolt through the center hole of 

the Tube Connector Clip (17) . 

A

 

Attach the Tube Connec-

tor Clip (17) to the Aluminum L Base (15) using the 5/16” 
bolt (16) with washer (19) and 5/16” Round Knob (20). 

B

.  

Using a  ¼”x 20x ¾” bolt (12), insert bolt as shown and se-
cure with ¼” x 20 Round Knob (2) and Washer (9). 

C

.  

Next, 

using a long ¼” x 20x 1” bolt (19), insert into clamp end of 
the Tube Connector Clip, secure with a 1/4” x 20 knob (2). 

D

Insert a T-bolt (14) into one of the holes on the Alumi-

num L Base at the bottom, thread on with a 1/4”x20 (2) 
round knob. Repeat this process (

D

) for the other hole at 

the bottom of the Base.

Studded T-Knob

Locking

Set Screw

D

.

 

T-Bolt

 

A

.

  5/16” Bolt

 

B

.

 3/4” x 20 Bolt

 

C

.

 1”x 1/4” x 20 Bolt

 

A

 

.

 5/16” Knob

& Washer

 

C

.

  1/4” x 20

Knob & Washer

 

D

.

 1/4” x 20

         Knob 

 

B

.

 

 1/4” x 20

Knob & Washer

Mounting Track

1

2

3

Summary of Contents for Big Sweep






Reviews: