background image

 

SeeGull

®

 EX

flex

®

 Reference Manual 

 

 

PCTEL, Inc., RF Solutions 

Page 11 

Revision F 

3.  Installation 

This section describes how to set up the 
SeeGull EXflex Scanning Receiver. 

 

3.1.  Integration 

There are sixteen (16) mounting holes (4-40 
screw) on the chassis of the unit that are 
used for mounting 

in the user’s 

enclosure/rack.  Note that the maximum 
depth of screw insertion from the chassis 
exterior is ¼”.  Refer t

Figure 3

 and 

Figure 

4

. Care should be taken when mounting this 

unit in a system enclosure, rack, or case, 
not to obstruct airways. Unobstructed 
convection airflow is recommended. 

 

 

Figure 3 - SeeGull EXflex Scanning Receiver top 
view. 

 

 

 

 

Airway intakes are located on the left and 
right sides of unit as shown in 

Figure 4

 and 

Figure 5

. Fan exhaust on rear of unit. 

 

 

 
 

Figure 4 - SeeGull EXflex Scanning Receiver side 

view 

 

 
 

 

 

 
 

Figure 5 - SeeGull EXflex Scanning Receiver rear 

view 

 
 
 

 

 
 
 
 
 
 
 
 
 
 

 
 

Note:

 Do not obstruct air intakes or exhaust 

on unit.  Do not place the unit intakes next 
to the exhaust of another heat source. 

Side air intakes 

Rear air exhaust 

Summary of Contents for SeeGull EXflex
























Reviews: