Model Number
102A 07
Revision: G
ECN #: 50860
P erfo rm an ce
EN G L ISH
SI
Measurement Range(for ±5V output)
50 psi
345 kPa
Useful Overrange(for ± 10V output)
100 psi
690 kPa
[1]
Sensitivity(± 15 %)
100 mV/psi
14.5 mV/kPa
Maximum Pressure(step)
500 psi
3,447 kPa
Maximum Pressure
(Total)
15,000 psi
103,421 kPa
Resolution
1 mpsi
0.007 kPa
Resonant Frequency
≥ 250 kHz
≥ 250 kHz
Rise Time(Reflected)
≤ 2.0 µ sec
≤ 2.0 µ sec
Low Frequency Response(- 5 %)
0.5 Hz
0.5 Hz
Non-Linearity
≤ 1.0 % FS
≤ 1.0 % FS
[2]
En viro n m en tal
Acceleration Sensitivity
≤ 0.002 psi/g
≤ 0.0014 kPa/(m/s²)
Temperature Range(Operating)
-100 to +275 °F
-73 to +135 °C
Temperature Coefficient of Sensitivity
≤ 0.03 %/°F
≤ 0.05 %/°C
Maximum Flash Temperature
3,000 °F
1,650 °C
Maximum Vibration
2,000 g pk
19,613 m/s² pk
Maximum Shock
20,000 g pk
196,133 m/s² pk
Electrical
Output Polarity(Positive Pressure)
Positive
Positive
Discharge Time Constant(at room temp)
≥ 1.0 sec
≥ 1.0 sec
Excitation Voltage
20 to 30 VDC
20 to 30 VDC
Constant Current Excitation
2 to 20 mA
2 to 20 mA
Output Impedance
< 100 Ohm
< 100 Ohm
Output Bias Voltage
8 to 14 VDC
8 to 14 VDC
Electrical Isolation
≥ 10
8
Ohm
≥ 10
8
Ohm
P h ysical
Sensing Geometry
Compression
Compression
Sensing Element
Quartz
Quartz
Housing Material
17-4 / 304L Stainless Steel
17-4 / 304L Stainless Steel
Thread Adaptor Material
17-4 Stainless Steel
17-4 Stainless Steel
Diaphragm
Invar
Invar
Sealing
Hermetic
Hermetic
Electrical Connector
10-32 Coaxial Jack
10-32 Coaxial Jack
Weight
0.39 oz
11.0 gm
[3]
All specifications are at room temperature unless otherwise specified.
In the interest of constant product improvement, we reserve the right to change specifications without notice.
ICP
®
is a registered trademark of PCB Piezotronics, Inc.
C A
- Ablative Coating
M
- Metric Mount
Supplied Accessory: Model 065A42 Floating clamp nut and thread seal, M10 x 1.0 thd. (1) replaces
Model 065B01
N
- Negative Output Polarity
S
- Stainless Steel Diaphragm
Diaphragm
316L Stainless Steel
316L Stainless Steel
W
- Water Resistant Cable
OP TION A L VERSION S
Optional versions have identical specifications and accessories as listed for the standard model except
where noted below. More than one option may be used.
N OTES:
[1]For +10 volt output, minimum 24 VDC supply voltage required. Negative 10 volt output may be
limited by output bias.
[2]Zero-based, least-squares, straight line method.
[3]See PCB Declaration of Conformance PS023 for details.
Date: 07/13/2020
Date: 07/13/2020
Date: 07/13/2020
Date: 07/13/2020
6373
Entered: LK
Engineer: NJL
Sales: RWM
Approved: RPF
Spec Number:
3425 Walden Avenue, Depew, NY 14043
Phone: 716-684-0001
Fax: 716-684-0987
E-Mail: [email protected]
SU P P L IED A C C ESSORIES:
Model 065B01 Floating clamp nut and thread seal 3/8-24 thd (1)
Summary of Contents for S102A07
Page 11: ......
