background image

Model Number

687A01

HANDHELD VIBRATION METER KIT

Revision: F

ECN #: 47534

Performance

ENGLISH

SI

Frequency Re10 to -20 %)

600 to 60,000 cpm

600 to 60,000 cpm

[4]

Frequency Response

(± 3 dB)

3 to 3000 kcpm

3 to 3000 kcpm

[4]

Acceleration Range

0.01 - 19.99 g rms

0.01 - 19.99 g rms

Resolution

± 2 counts

± 2 counts

[1]

Velocity Range

0.001 - 1.999 in/sec rms

NA

Accuracy

± 3 %

± 3 %

[1]

Environmental

Temperature Range(Accelerometer)

-65 to +250 °F

-54 to +121 °C

Temperature Range

(Meter)

+32 to +122 °F

0 to +50 °C

[3]

Electrical

Excitation Voltage(± 1 VDC)

24 VDC

24 VDC

Constant Current Excitation(± 0.6 mA)

2 mA

2 mA

Bias Voltage

0.00 to 19.99 VDC

0.00 to 19.99 VDC

Battery Life(Alkaline)

10 hours

10 hours

[1]

Battery Life

(Rechargeable Ni Cad)

3 hours

3 hours

[1][2]

Physical

Size (Length x Width x Height)

15 in x 11 in x 4.375 in

381 mm x 279.4 mm x 111.1 mm

Weight

3.90 lb

1.77 kg

Connector(Input)

BNC Jack

BNC Jack

Connector

(Headphones)

1/8" Stereo Jack

1/8" Stereo Jack

ROHS Compliant

No

No

All specifications are at room temperature unless otherwise specified.
In the interest of constant product improvement, we reserve the right to change specifications without notice.

ICP

®

is a registered trademark of PCB Group, Inc. 

OPTIONAL VERSIONS

Optional versions have identical specifications and accessories as listed for the standard model 

except where noted below. More than one option may be used.

R

- Rechargeable option, includes rechargable batteries and charger.

Supplied Accessory : Model 017A01 Power Cord (1)
Supplied Accessory : Model 073A09 Rechargeable NiCad battery (9V) (1)
Supplied Accessory : Model 073M12 External Charger (1)

NOTES:

[1] Typical value.
[2] Varta TR7/8 or Eveready N88 for rechargeable version.
[3] Non-condensing.
[4] 1Hz = 60 cpm (cycles per minute).

SUPPLIED ACCESSORIES: 

Model 050BQ006AC Coiled ployurethane cable, right angle composite 2-socket MIL to BNC 
plug, 6' extended length (1)
Model 070A47 Stereo Headphones with indvidual volume controls (for 687A01 & 687A02) (1)
Model 080A131 Flat surface magnet 0.75" diameter 15 lb. force stainless steel knurled case, 
includes removable stud (1)
Model 603C01 Sensor 100 mV/g ±20% (1)
Model 687A02 Handheld vibration meter measures acceleration, velocity, and complies with 
ISO 2954 & ISO 10816 (1)

Entered: LK

Engineer: RB

Sales: MC

Approved: BAM

Spec Number:

Date: 5/15/2018

Date: 5/15/2018

Date: 5/15/2018

Date: 5/15/2018

11284 

3425 Walden Avenue, Depew, NY 14043

Phone: 800-959-4464
Fax: 716-684-3823
E-Mail: [email protected]

Summary of Contents for IMI Sensors 687A01






































































Reviews: