PCB Piezotronics IMI SENSORS 604B11, Installation And Operating Manual

Page: 18 / 19

Model Number
604B11
LOW-COST TRIAXIAL INDUSTRIAL ICP® ACCELEROMETER
Revision: B
ECN #: 49214
Performance ENGLISH SI
Sensitivity(± 20 %) 100 mV/g 10.2 mV/(m/s²)
[2]
Measurement Range ± 50 g ± 490 m/s²
Frequency Range(± 3 dB) 30 to 300,000 cpm 0.5 to 5000 Hz
Resonant Frequency 600 kcpm 10 kHz
[1]
Broadband Resolution(1 to 10,000 Hz) 350 µg
3434 µm/sec
2 [1]
Non-Linearity ± 1 % ± 1 %
[3]
Transverse Sensitivity ≤ 5 % ≤ 5 %
Environmental
Overload Limit(Shock) 5000 g pk 49,050 m/s² pk
Temperature Range -65 to +250 °F -54 to +121 °C
Temperature Response See Graph See Graph
[1]
Enclosure Rating IP68 IP68
Electrical
Settling Time(within 1% of bias) ≤ 2.0 sec ≤ 2.0 sec
Discharge Time Constant ≥ 0.3 sec ≥ 0.3 sec
Excitation Voltage 18 to 28 VDC 18 to 28 VDC
Constant Current Excitation 2 to 20 mA 2 to 20 mA
Output Impedance <150 Ohm <150 Ohm
Output Bias Voltage 8 to 12 VDC 8 to 12 VDC
Spectral Noise(10 Hz) 8 µg/√Hz
78.5 (µm/sec
2
)/√Hz
[1]
Spectral Noise (100 Hz) 5 µg/√Hz
49.1 (µm/sec
2
)/√Hz
[1]
Spectral Noise (1 kHz) 4 µg/√Hz
39.2 (µm/sec
2
)/√Hz
[1]
Electrical Isolation(Case)
>10
8
Ohm >10
8
Ohm
Physical
Size (Diameter x Height) 1.38 in x 1.00 in 35.1 mm x 25.4 mm
Weight(without cable) 4.0 oz 113.3 gm
Mounting Thread 1/4-28 UNF Not Applicable
[4]
Mounting Torque 2 to 5 ft-lb 2.7 to 6.8 Nm
Sensing Element Ceramic Ceramic
Sensing Geometry Shear Shear
Housing Material Stainless Steel Stainless Steel
Sealing Welded Hermetic Welded Hermetic
Electrical Connector Molded Integral Cable Molded Integral Cable
Electrical Connection Position Side Side
Electrical Connections(Red) X axis X axis
Electrical Connections (Green) Y axis Y axis
Electrical Connections (White) Z axis Z axis
Electrical Connections (Black) Ground Ground
Cable Length 10 ft 3.0 m
Cable Type Polyurethane Polyurethane
[5]
[6]
[7]
All specifications are at room temperature unless otherwise specified.
In the interest of constant product improvement, we reserve the right to change
specifications without notice.
ICP
®
is a registered trademark of PCB Group, Inc.
OPTIONAL VERSIONS
Optional versions have identical specifications and accessories as listed for the standard model
except where noted below. More than one option may be used.
EX
- Hazardous Area Approval- contact factory for specific approvals
M
- Metric Mount
Supplied Accessory : Model M081A68 Captive mounting bolt M6 x 1 (1)
NOTES:
[1] Typical.
[2] Conversion Factor 1g = 9.81 m/s².
[3] Zero-based, least-squares, straight line method.
[4] 1/4-28 has no equivalent in S.I. units.
[5] Twisted shielded 4-conductor cable.
[6] See PCB Declaration of Conformance PS023 or PS098 for details.
[7] See Model's “Instructions For Use” (IFU) for North American Conformity and Certification
Statements.
SUPPLIED ACCESSORIES:
Model 081A68 Captive mounting bolt 1/4-28 x .90" (1)
Model ACS-2T NIST Traceable Single Point Calibration at 100 Hz for Each Axis (1)
Entered: LK Engineer: gs Sales: MC Approved: BAM Spec Number:
Date: 3/13/2019 Date: 3/13/2019 Date: 3/13/2019 Date: 3/13/2019
21047
3425 Walden Avenue, Depew, NY 14043
Phone: 800-959-4464
Fax: 716-684-3823
E-Mail: imi@pcb.com