PCB Piezotronics ICP 101A Series, Installation And Operating Manual, Page: 9 / 10

Model Number
101A06
ICP® PRESSURE SENSOR
Revision: E
ECN #: 44786
Performance ENGLISH SI
Measurement Range(for ±5V output) 500 psi 3450 kPa
Useful Overrange(for ± 10V output) 1000 psi 7900 kPa [1]
Sensitivity(± 1 mV/psi) 10 mV/psi 1.45 mV/kPa
Maximum Pressure(static) 5000 psi 34,500 kPa
Resolution 0.01 psi 0.07 kPa
Resonant Frequency ≥ 400 kHz ≥ 400 kHz
Rise Time(Reflected) ≤ 1.5 µ sec ≤ 1.5 µ sec
Low Frequency Response(-5 %) 0.01 Hz 0.01 Hz
Non-Linearity ≤ 2.0 % FS ≤ 2.0 % FS [2]
Environmental
Acceleration Sensitivity ≤ 0.002 psi/g ≤ 0.0014 kPa/(m/s²)
Temperature Range(Operating) -100 to +275 °F -73 to +135 °C
Temperature Coefficient of Sensitivity ≤ 0.03 %/°F ≤ 0.054 %/°C
Maximum Flash Temperature 3000 °F 1650 °C
Maximum Shock 20,000 g pk 196,000 m/s² pk
Electrical
Output Polarity(Positive Pressure) Positive Positive
Discharge Time Constant(at room temp) ≥ 50 sec ≥ 50 sec
Excitation Voltage 20 to 30 VDC 20 to 30 VDC
Constant Current Excitation 2 to 20 mA 2 to 20 mA
Output Impedance ≤ 100 Ohm ≤ 100 Ohm
Output Bias Voltage 8 to 14 VDC 8 to 14 VDC
Electrical Isolation
10
8
Ohm 10
8
Ohm
Physical
Sensing Geometry Compression Compression
Sensing Element Quartz Quartz
Housing Material Stainless Steel Stainless Steel
Diaphragm Invar Invar
Sealing Welded Hermetic Welded Hermetic
Electrical Connector 10-32 Coaxial Jack 10-32 Coaxial Jack
Weight 0.44 oz 12.5 gm
All specifications are at room temperature unless otherwise specified.
In the interest of constant product improvement, we reserve the right to change specifications without notice.
ICP
®
is a registered trademark of PCB Group, Inc.
H
- Hermetic Seal
Sealing Welded Hermetic Welded Hermetic
M
- Metric Mount
Supplied Accessory : Model 065A40 Seal ring 0.435" OD x 0.397" ID x 0.030" thk brass (3)
replaces Model 065A03
N
- Negative Output Polarity
S
- Stainless Steel Diaphragm
Diaphragm 316L Stainless Steel 316L Stainless Steel
W
- Water Resistant Cable
NOTES:
[1]For +10 volt output, minimum 24 VDC supply voltage required. Negative 10 volt output may be
limited by output bias.
[2]Zero-based, least-squares, straight line method.
[3]See PCB Declaration of Conformance PS023 for details.
SUPPLIED ACCESSORIES:
Model 065A03 Seal ring 0.435" OD x 0.377" ID x 0.030" thk brass (3)
3425 Walden Avenue, Depew, NY 14043
Phone: 716-684-0001
Fax: 716-684-0987
E-Mail: info@pcb.com
[3]
OPTIONAL VERSIONS
Optional versions have identical specifications and accessories as listed for the standard model
except where noted below. More than one option may be used.
Entered: LK Engineer: BAM Sales: RWM Approved: BAM Spec Number:
Date: 11/4/2015 Date: 11/4/2015 Date: 11/4/2015 Date: 11/4/2015
5957