PCB Piezotronics 401B04, Installation And Operating Manual

Page: 8 / 9

Model Number
401B04
ICP® SOURCE FOLLOWER
Revision: F
ECN #: 52519
P erfo rm an ce EN G L ISH SI
Gain(+ 0 to -2 %) 1 1
Output Range ± 5 V ± 5 V
Low Frequency Response 0 Hz 0 Hz
High Frequency Response(2.0 mA) 110 kHz 110 kHz [1]
High Frequency Response (4 mA) 220 kHz 220 kHz [1]
High Frequency Response (20 mA) 1,000 kHz 1,000 kHz [1]
Non-Linearity ≤ 2 % FS ≤ 2 % FS
En viro n m en tal
Temperature Range(Operating) +30 to +150 °F -1.1 to +65.5 °C
Electrical
Excitation Voltage + 18 to 30 VDC + 18 to 30 VDC [2]
Constant Current Excitation 2 to 20 mA 2 to 20 mA
Output Impedance < 100 Ohm < 100 Ohm
Output Bias Voltage + 7 to 14 VDC + 7 to 14 VDC
Output Current 1 to 19 mA 1 to 19 mA [3]
Broadband Electrical Noise(10 to 100,000
kHz) 12 µV rms 12 µV rms [4]
Spectral Noise(1 Hz) 4 µV/√Hz 4 µV/√Hz [4]
Spectral Noise (10 Hz) 1 µV/√Hz 1 µV/√Hz [4]
Spectral Noise (100 Hz) 0.3 µV/√Hz 0.3 µV/√Hz [4]
Spectral Noise (1 kHz) 0.1 µV/√Hz 0.1 µV/√Hz [4]
Spectral Noise (10 kHz) 0.05 µV/√Hz 0.05 µV/√Hz [4]
Insulation Resistance(Minimum)
10
9
Ohm 10
9
Ohm
P h ysical
Housing Material Aluminum Aluminum
Electrical Connector(Input) BNC Plug BNC Plug
Electrical Connector (Output) BNC Jack BNC Jack
Size (Length x Width x Height) 2.2 in x 1.1 x 0.9 55.9 mm x 27.9 x 22.9
Weight 2.50 oz 70.9 gm
[5]
All specifications are at room temperature unless otherwise specified.
In the interest of constant product improvement, we reserve the right to change specifications without notice.
ICP
®
is a registered trademark of PCB Piezotronics, Inc.
OP TION A L VERSION S
Optional versions have identical specifications and accessories as listed for the standard model except
where noted below. More than one option may be used.
N OTES:
[1]Above stated frequency, the amplifier becomes slew rate limited.
[2]Voltage < 20 VDC reduces input range to ±3V.
[3]Excitation current supplied minus 1 mA nominal current consumption.
[4]Typical, tested with 1000 pF capacitance at input.
[5]See PCB Declaration of Conformance PS024 for details. A low impendance connection from case
to earth ground is required to maintain CE compliance.
Date: 01/27/2022 Date: 01/27/2022 Date: 01/27/2022 Date: 01/27/2022 40857
Entered: TP Engineer: CPH Sales: AH Approved: JWH Spec Number:
Phone: 716-684-0001
Fax: 716-684-0987
E-Mail: info@pcb.com
3425 Walden Avenue, Depew, NY 14043