PCB Piezotronics 106B51, Installation And Operating Manual

Page: 9 / 11

Model Number
106B51
ICP® PRESSURE SENSOR
Revision: B
ECN #: 45338
Performance ENGLISH SI
Measurement Range(for ±5V output) 5 psi 35 kPa
Useful Overrange 10 psi 69 kPa [1]
Sensitivity(± 15 %) 1000 mV/psi 145 mV/kPa
Maximum Pressure(step) 100 psi 690 kPa
Maximum Pressure(static) 500 psi 3448 kPa
Resolution 0.05m psi .00034 kPa
Resonant Frequency ≥ 40 kHz ≥ 40 kHz
Rise Time ≤ 12 µ sec ≤ 12 µ sec
Low Frequency Response(-5 %) 0.5 Hz 0.5 Hz
Non-Linearity ≤ 1 % FS ≤ 1 % FS [2]
Environmental
Acceleration Sensitivity ≤ 0.002 psi/g ≤ 0.0014 kPa/(m/s²)
Temperature Range(Operating) -65 to +250 °F -54 to +121 °C
Temperature Range(Operating) -65 to +250 °F -54 to +121 °C
Temperature Coefficient of Sensitivity ≤ 0.03 %/°F ≤ 0.054 %/°C
Maximum Flash Temperature 3000 °F 1649 °C
Maximum Vibration 500 g pk 4903 m/s² pk
Maximum Shock 1000 g pk 9807 m/s² pk
Electrical
Output Polarity(Positive Pressure) Positive Positive
Discharge Time Constant(at room temp) ≥ 1 sec ≥ 1 sec
Excitation Voltage 20 to 30 VDC 20 to 30 VDC
Constant Current Excitation 2 to 20 mA 2 to 20 mA
Output Impedance ≤ 100 Ohm ≤ 100 Ohm
Output Bias Voltage 8 to 14 VDC 8 to 14 VDC
Physical
Sensing Element Quartz Quartz
Housing Material 17-4 Stainless Steel 17-4 Stainless Steel
Diaphragm 316L Stainless Steel 316L Stainless Steel
Sealing Welded Hermetic Welded Hermetic
Electrical Connector 10-32 Coaxial Jack 10-32 Coaxial Jack
Weight 1.13 oz 32 gm
All specifications are at room temperature unless otherwise specified.
In the interest of constant product improvement, we reserve the right to change specifications without notice.
ICP
®
is a registered trademark of PCB Group, Inc.
E
- Emralon coating
Coating Emralon Emralon
Electrical Isolation
10
8
Ohm 10
8
Ohm
J
- Ground Isolated
N
- Negative Output Polarity
W
- Water Resistant Cable
Supplied Accessory : Model 060A11 Acetal clamp nut 3/4-16-2A thd 3/4" hex (1)
WM
- Water Resistant Cable
Supplied Accessory : Model 060A13 Metric Acetal clamp nut M20 x 1.5-6g thd 20 mm hex (1)
NOTES:
[1]For +10 volt output, minimum 24 VDC supply voltage required. Negative 10 volt output may be
limited by output bias.
[2]Zero-based, least-squares, straight line method.
[3]See PCB Declaration of Conformance PS023 for details.
SUPPLIED ACCESSORIES:
Model 060A11 Acetal clamp nut 3/4-16-2A thd 3/4" hex
Model 060A13 Metric Acetal clamp nut M20 x 1.5-6g thd 20 mm hex (1)
Model 065A36 Seal, .687" OD x .625" ID x .060", Derlin (3)
3425 Walden Avenue, Depew, NY 14043
Phone: 716-684-0001
Fax: 716-684-0987
E-Mail: info@pcb.com
[3]
OPTIONAL VERSIONS
Optional versions have identical specifications and accessories as listed for the standard model
except where noted below. More than one option may be used.
Entered: LK Engineer: BAM Sales: MFG Approved: RPF Spec Number:
Date: 4/7/2016 Date: 4/7/2016 Date: 4/7/2016 Date: 4/7/2016
23894