background image

13

Date

The date format is <day-of-the-week>. <day> <month> <year>.
Press <F3> to  display the calendar.

T i m e

The time format is <hour> <Minute> <second> displayed in
24-hour military-time clock. For example, 1 p. m. is displayed
as 13:00:00.

Primary

These categories identify the types of the two channels that

Master/Primary

have been installed in the computer.

Slave/Secondary
Master/Secondary 
If you select Type “Manual”, you will need to know the information
Slave

listed below. Enter the information directly from the  keyboard
and press <Enter>. This information should be included in the
documentation from your hard disk vendor or the system
manufacturer.

If the controller of the HDD interface is SCSI, the selection
shall be “None”.

If you select Type “Auto”, the BIOS will auto-detect the HDD
and CD-ROM drive at the POST stage and show the IDE for
the HDD and CD-ROM drive.
TYPE

-Drive type

CYLS

-Number of cylinders

HEADS

-Number of heads

PRECOMP

-Write precom

LANDZONE

-Landing zone

SECTORS

-Number of sectors

MODE

-Mode  type

If a hard disk has not been installed, select NONE and
press <Enter>.

Drive A Type /

This category identifies the types of floppy disk drive A or

Drive B Type

drive B that has been installed in the computer.

Video

The default setting is EGA/VGA.

BIOS Setup

Summary of Contents for 357757 Series

















Reviews: