background image

 

62 

 

 

MO9740 Manual 

Barcodes 

Code 39, Extended Code 39, Code 93, Code 128 
UCC 
Code 128(Subset A, B, C) Codabar, Interleave 2 of 
5, EAN-8 2&5 add on, EAN-13, EAN-128, UPC, 
UPC-A, E 2&5 add on, POSTNET, German POST, 
Matrix 25 

2D Barcodes 

Maxicode, PDF-417, 

Graphic 

PCX bit map, GDI graphics 

Software 

Eltron Language compatible 
Windows Driver (98/2000/NT/XP) 
Speedy Label Lite – label design software   
Label editing software – ArgoBar 
Print Utility 

Media 

Roll-feed, die-cut, continuous, fan-fold, tags, ticket 
in thermal paper or plain paper and fabric label 
Max width 4.25” (108 mm) 
Min width 1.0” (25.4 mm) 
Thickness .0025”~. 01” (.0635mm ~. 254mm) 
Max roll capacity 5” (127 mm) OD 
Core size 1” (25mm) ID 

Ribbon 

Wax, Wax/Resin, Resin (Outside coating ribbon) 
Ribbon width – 2”, 4” 
Ribbon roll – max OD 1.5” (38 mm) 
Ribbon length – max 1182’ (100 M) 
Core size - ID 0.5” core (13 mm) with notch 

Mechanism 
request 

Build-in Tear off bar, front-open cover, clear window, 
fan fold paper back cover, same mechanism 
structure, face-out ribbon run way, face-in media 
run way, un-adjustable TPH carrier 

Power source 

110/220 VAC ± 10%, 50/60 Hz, external power 
adapter 

Agency listing 

CE, UL, CUL, FCC class A, CCC 

Operation 
environment 

40ºF ~ 100ºF (4ºC~38ºC) ; 10~90% non 
condensing 

Optional items 

Cutter, Dispenser kit, Real time clock card, 
PaxarNet print server, offline keypad, 2MB Asian 
Font card (Traditional Chinese, Simplified Chinese, 
Korean and Japanese) 

 

63 

MO9740 Manual 

Fonts, Bar Codes and Graphics Specification 

 

The specifications of fonts, bar codes and graphics depend on the 
printer emulation. The emulation PPLB is a printer programming 
language, through which the host can communicate with your 
printer.  

 

 

Printer Programming Language B, PPLB 

 

Specification

 

MO9742PEx MO9742PEx 

General fonts 5 fonts with different point sizes

 

Symbol sets 
(Code pages)

8 bits: code page 437, 850, 852, 860, 
863,865,857,861,862,855,866,737,851,869 and 
Windows 1250,1251,1252,1253.1254,1255.   
7 bits: USA, British, German, French, Danish, Italian, 
Spanish, Swedish and Swiss.

 

Soft fonts

 

Downloadable soft fonts

 

Font 
expandability

1x1 to 24x24

 

Bar code 
types

 

Code 39(checksum), Code 93, Code 128/ subset 
A,B,C, Codabar, Interleave 2 of 5(checksum), Matrix 
25, UPC A/E 2 and 5 add-on, EAN-8/13, Code 
128UCC, UCC/EAN, Postnet, German Postcode. 
MaxiCode and PDF417 (2D symbologies)

 

Graphics

 

PCX and binary raster

 

   
Notes : 

1. The bare core for ribbon must be 11 cm in length. It should 

have two opposite slits at two ends. If the ribbon itself is 
less than 11 cm, it has to be aligned with the bare core at left 
end when you install it. 

Summary of Contents for MO 9742




































Reviews: