PAX SK800 Installation Manual Download Page 9

5) If necessary, please contact PAX technical support for assistance with the device. 
6) Before using the magnetic stripe /IC/contactless card, check if there is any suspicious 
person nearby, if so, pay attention to guard against theft. 

8

FCC Regulations: 

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two 
conditions: (1) This device may not cause harmful interference, and (2) this device must accept 
any interference received, including interference that may cause undesired operation. 
 
This equipment has been tested and found to comply with the limits for a Class B digital device, 
pursuant to Part 15 of the FCC Rules.   These limits are designed to provide reasonable protection 
against harmful interference in a residential installation. This equipment generates, uses and can 
radiate radio frequency energy and, if not installed and used in accordance with the instructions, 
may cause harmful interference to radio communications.   However, there is no guarantee that 
interference will not occur in a particular installation.   If this equipment does cause harmful 
interference to radio or television reception, which can be determined by turning the equipment 
off  and on, the user is encouraged to try to correct the interference by one of the following 
measures: 

 

Reorient or relocate the receiving antenna. 

 

Increase the separation between the equipment and receiver. 

 

Connect the equipment into an outlet on a circuit different from that 

to which the receiver is connected. 

 

Consult the dealer or an experienced radio/TV technician for help. 

FCC Caution: 

 

Any changes or modifications not expressly approved by the party responsible for 
compliance could void the user's authority to operate this equipment. 

 

This transmitter must not be co-located or operating in conjunction with any other antenna 
or transmitter. 

Radiation Exposure Statement:

 

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled 
environment. This equipment should be installed and operated with minimum distance 20cm 
between the radiator & your body.

 

ISED Notice 

 

This device complies with Science and Economic Development Canada

s license-exempt 

RSS standard(s). Operation is subject to the following two conditions:   
1)

 

this device may not cause interference, and   

2)

 

this device must accept any interference, including interference that may cause 
undesired operation of the device. 

 

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils 
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:   

Summary of Contents for SK800












Reviews: