Pax Technology D200WB Manual Download Page 7

Absorption Rate, or SAR.   The SAR limit set by the FCC is 1.6W/kg.    

 

The  FCC  has  granted  an  Equipment  Authorization  for  this  model  device  with  all  reported 

SAR  levels  evaluated  as  in  compliance  with  the  FCC  RF  exposure  guidelines.   SAR 

information on this model device is on file with the FCC and can be found under the Display 

Grant section o

www.fcc.gov/oet/ea/fccid

 after searching on FCC ID: V5PD200WB.

 

 

For this device, the highest reported SAR value for near the body is 0.99 W/kg. 

 

While  there  may  be  differences  between  the  SAR  levels  of  various  devices  and  at  various 

positions, they all meet the government requirement. 

 

SAR compliance for body operation is based on a separation distance of  0  mm between the 

unit and the human body.  

 

IC Notice

 

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject 

to the following two conditions:   

(1) this device may not cause interference, and   

(2)  this  device  must  accept  any  interference,  including  interference  that  may  cause  undesired 

operation of the device. 

 

Le  présent  appareil  est  conforme  aux  CNR  d'Industrie  Canada  applicables  aux  appareils  radio 

exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:   

(1) l'appareil ne doit pas produire de brouillage, et   

(2)  l'utilisateur  de  l'appareil  doit  accepter  tout  brouillage  radioélectrique  subi,  même  si  le 

brouillage est susceptible d'en 

 

This Class B digital apparatus complies with Canadian ICES-003. 

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. 

 

IC: 11689A-D200WB 

 

IC Radiation Exposure Statement 

This EUT is compliance with SAR for general population/uncontrolled exposure 

limits in IC RSS-102 and had been tested in accordance with the measurement 

methods and procedures specified in IEEE 1528 and IEC 62209. This equipment 

should be installed and operated with minimum distance 0 cm between the 

radiator and your body. This device and its antenna(s) must not be co-located or 

operating in conjunction with any other antenna or transmitter. 

 

Summary of Contents for D200WB









Reviews: